Haier HWM100-828A Washer User Manual


 
A
<10cm
A
B
<1.5m
5
> 30mm
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and
cost such long time that the machine may stop
at mid way.
2.Do not step on or press the drain hose.
4.If extra drain hose is needed, please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
length shall not exceed 1.5m.
3. If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
Usage the drain hose
5.If the extra hose is too long, cut it either at A
or at B.
<2
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
Fasten
Loosen
High
Low
the adjustable nut
the adjustable leg
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 . After adjustment, fasten the nut.
Adjust the Installation position
1312
For the MEMORY,BLANKET,CHILD,STANDARD programs push the RINSE botton light
select the rinse times Overflow rinse.1.2.3.
is flashing ,
then push
Press the Wash button to select a wash time, from the MEMORY,BLANKET, CHILD ,SPEEDY, STANDARD
programs.
Press the Wash button can select or cancel the process of wash ,but can not change time from
the SILK programs.
The button is unavailable from the SPEEDY and WOOL programs.
"WASH " button
Press the button to select spin time, from the MEMORY,BLANKET,JEAN,STANDARD program."SPIN "
Press change time
from the SILK programs.
"SPIN"buttoncan select or cancel the process of spin ,but can not
E "SPIN " button
WATER
Common, memory and standard procedures for washing machine automatically detects the amount of cloth,
the water level is automatically set to 4.6.8 in an appropriate level. Into the wet clothing, may be set to "8" level,
the user needs to choose the appropriate level.
Due to different levels of wet and dry cloth to determine the actual water level may be different;
During the period of "washing" and "rinse", hold down the "water" button fill water, hand release or overflow water
to stop when reached the water level.
Wool, silk program level only can be choosen between 4-8 level, blanket water level of the program to
select between 2-5
LEVEL
F WATER LEVEL button""
G button" RYING" D "
Push the "AIR DRY" button to select air dry procedure. The program is chosen(0.5h 1.0h 2.0h).
0.5 1.0h The purpose is drying the inner tub and the outer tub, which can avoid growing
mildew on the outer tub and the inner tub.
2.0h can dry laundries The max drying capacity of the fibre laundrie is 2.0 kg.
"AIR DRY"program can not be reserved
AIR DRY
The button is unavailable from the SPEEDY and TUB DRY programs.
For ECONOMY ,WOOL programs, press can not change time"RINSE"button
G button"AIR DRY"
H button"RINSE"
WASH
SPIN
RINSE
The button is unavailable from the SPEEDY and WOOL programs.
If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .
Washing machines began to work, to manually change the level, press the "start pause" button re-select.
In common, strong, children, standards, and the memory process, the rinse water when washing the water level
higher than that of a file (the highest water level and artificial selection, except when rinse water)