Blomberg WNF 8543 AE20 Washer User Manual


  Open as PDF
of 51
 
3 - EN
2 Installation
RefertothenearestAuthorisedServiceAgentfor
installation of the product. To make the product
ready for use, review the information in the
user manual and make sure that the electricity,
tap water supply and water drainage systems
areappropriatebeforecallingtheAuthorized
ServiceAgent.Iftheyarenot,callaqualified
technicianandplumbertohaveanynecessary
arrangements carried out.
C
Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer's
responsibility.
B
 Installationandelectricalconnectionsof
theproductmustbecarriedoutbythe
AuthorizedServiceAgent.Manufacturershall
notbeheldliablefordamagesthatmayarise
fromprocedurescarriedoutbyunauthorized
persons.
A
Prior to installation, visually check if the
producthasanydefectsonit.Ifso,donot
haveitinstalled.Damagedproductscause
risks for your safety.
C
Makesurethatthewaterinletanddischarge
hosesaswellasthepowercablearenot
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.
Appropriate installation location
• Placethemachineonarigidfloor.Donot
place it on a long pile rug or similar surfaces.
• Totalweightofthewashingmachineandthe
dryer-withfullload-whentheyareplaced
on top of each other reaches to approx.
180kilograms.Placetheproductonasolid
and flat floor that has sufficient load carrying
capacity!
• Donotplacetheproductonthepower
cable.
• Donotinstalltheproductatplaceswhere
temperaturemayfallbelow0ºC.
• Placetheproductatleast1cmawayfrom
the edges of other furniture.
Removing packaging reinforcement
Tiltthemachinebackwardstoremovethe
packaging reinforcement. Remove the packaging
reinforcementbypullingtheribbon.
Removing the transportation locks
A
 Donotremovethetransportation
locksbeforetakingoutthepackaging
reinforcement.
A
 Removethetransportationsafetybolts
beforeoperatingthewashingmachine,
otherwise,theproductwillbedamaged.
1. Loosenalltheboltswithaspanneruntilthey
rotatefreely(C).
2. Removetransportationsafetyboltsby
turning them gently.
3. Attachtheplasticcoverssuppliedinthe
UserManualbagintotheholesontherear
panel. (P)
C
Keepthetransportationsafetyboltsinasafe
place to reuse when the washing machine
needstobemovedagaininthefuture.
C
Nevermovetheproductwithoutthe
transportationsafetyboltsproperlyfixedin
place!
Connecting water supply
C
Thewatersupplypressurerequiredtorun
theproductisbetween1to10bars(0.1
–10MPa).Itisnecessarytohave10–80
liters of water flowing from the fully open
tap in one minute to have your machine run
smoothly.Attachapressurereducingvalveif
water pressure is higher.
C
Ifyouaregoingtousethedoublewater-inlet
productasasingle(cold)water-inletunit,
you must install the supplied stopper to the
hotwatervalvebeforeoperatingtheproduct.
(Appliesfortheproductssuppliedwitha
blindstoppergroup.)
C
Ifyouwanttousebothwaterinletsofthe
product, connect the hot water hose after
removing the stopper and gasket group from
thehotwatervalve.(Appliesfortheproducts
suppliedwithablindstoppergroup.)
A
 Modelswithasinglewaterinletshouldnot
beconnectedtothehotwatertap.Insuch
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
A
 Donotuseoldorusedwaterinlethoses
onthenewproduct.Itmaycausestainson
your laundry.
1. Connectthespecialhosessuppliedwiththe
product to the water inlets on the product.
Redhose(left)(max.90ºC)isforhotwater
inlet,bluehose(right)(max.25ºC)isforcold
water inlet.
A
 Ensurethatthecoldandhotwater
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end of the
 previous next