Beko WML 15080 DB Washer/Dryer User Manual


 
-4- EN
inlet hoses. Clean the top of the water inlet valve lter with a
brush. If lters are extremely clogged you can pull it out with a
pincer. Youcantakeouttheflatsideofwaterinlethoseswithits
sealandcleanwithtapwater.
Hose
Thereisriskoffreezingincoldregion,ifyourmachineisplaced
inacoldplaceremainingwaterinhosesmustbedrainedwith
pumpfilterwhenmachineisnotused.Waterinlethosescanbe
drainedbytakingitoutfromtap.
Cleaning Pump Filter
• Clean the foreign substance filter
periodically at least for once!
• If the foreign substances (coins, buttons, baby socks and
etc.) clog the foamy water pump, clean the filter.
• Before cleaning, empty the water that remains inside first.
• Hot water danger: There may be 15 liters of hot water at
90°C in the machine. Open the filter carefully.
Drain the water completely in the following situations...
• before cleaning the foreign substance filter;
• before transporting the machine ( for example moving into
a new house);
• when there is a risk of freezing.
1. Turn off the appliance, unplug the power cable and close
the tap. Wait for the hot soapy water to cool enough. Other-
wise, there is a risk of scalding.
2. Open the service cover by pressing the button. In order
to prevent the little amount of water that is inside pump spill-
ing over the floor, put a container in front of the filter cover.
Take out the filter by turning anticlockwise.
3. To loosen the foreign substance filter, turn it half turn
(anticlockwise) and take the remaining water with a cloth.
When there is no water, turn the foreign substance filter until
it is totally released and take it out.
4. Clean the foreign substance filter and pump opening.
5. Reinstall the foreign substance filter and turn it tightly
(clockwise).
6. Close the service cover.
1. Removing the transportation safety bolts
Before the washing machine is operated, the transit bars must
be removed! In order to do this:
1. Loosen “C” bolts by rotating them counter clockwise with a
suitable spanner
2. Remove transportation safety bolts by turning.
3. Place “P” plastic covers onto the openings of transportation
locks by rotating in direction of arrow and pushing.
Attention please! Keep the transit safety bolts for using when
machine is to be transported again. Always transport your
machine with transportation locks.
2. Leveling the feet
In order to operate your machine without
noise and vibration it must be properly on
balance. Four feet of your machine can be
adjusted. First loosen the plastic counter
bolt. Tighten the counter bolt after adjusting
the feet for leveling your machine.
3. Water Connections
a) Water Inlet Hose: Your machine is connect-
ed to water supply by special hoses supplied
by the machine.
There are plastic seals on hose or plastic bag
for eliminating any leakage in connections
points. These seals must be used on each
side of the connection. Seals on machine side must be con-
nected lter cannal.
After connecting the hose, check all connections for leaks In
order to eliminate any risk due to water leakage keep the taps
o when machine is not used.
Your machine will operate eciently if the water from tap is
minimum 1 and maximum 10 bars. Practically 1 bar means 8
liters of water in one minute when tap is fully on.
Connect hose to the machine. Tighten bolts with hand power,
do not use spanner.
Do not connect single inlet machine to hot water. If machine is
connected with Y part to a double inlet and over 40˚C for single
inlet machines, machine may switch to protection mode.
b) Water drain hose: Water drain hose could be placed either
at the side of the bath tub, or directly to the drain. The hose
should not be bent. Water drain hose should be secured with
the holder so that it would not fall down on the ground.
The hose should be placed between 40 and 100 cm. from the
ground. Water drain hose could be placed directly to the drain
water inlet.
4. Electrical connection
Connect the power cord to the appropirate electrical system
which is being supported by the maximum voltage and current
rating indicated on the rating plate placed on the washing
machine.
Look! Page 1, Steps before operating Fullautomatic Wash-
ing Machine and safety precautions. Make sure that you have
grounded power outlet.
You turned the machine on, but the leds are off on the
panel.
Check the grounding on the power cable or a blown fuse.
Check the front door proper closure.
Machine does not take water.
Check the front door for proper closure. Either taps are closed
or water intake lters are clogged.
Taken water is directly discharged.
Check if the discharge hose placed as described in the users
manual or not.
Water coming from beneath the machine.
Check the water intake and drain hoses. Tighten the connec-
tions. The washers of the hoses may be worn out. If non of the
both, the pump lter is not closed properly.
Foam coming out of the detergent dispenser.
Check whether your detergent is suitable for automatic ma-
chines. Next time use less detergent.
Pump does not drain water.
Clean the pump lter. Check whether the drain hose is bent or
not. If there is need to clean the pump lter, refer to the pump
lter cleaning section of the manual.
Installation
6
Before calling service
7