Beko WML 15080 DB Washer/Dryer User Manual


 
-3- EN
Detergent Dispenser
Powder detergent residue may accumulate in drawer after a
while. In order to clean detergent drawer press the marked
point of the siphon on softener compartment and push the
drawer towards yourself. Wash the drawer with water
Siphon
Do not neglect cleaning suction cup when it becomes soiled.
In order take suction cup out rst take detergent drawer out.
Clean it in order to eliminate blocking by softener residue. After
cleaning place suction cup to its place and make sure it is
placed properly.
Water Inlet Filters
There is a lter at each at end where water inlet hose is con-
nected to tap and at each of water inlet valve placed behind
the machine. These lters blocks entrance of foreign objects
and dirts to the machine. Filters must be cleaned regularly to
avoid clogging. For doing this, turn o tap water. Pull out water
5
Care and maintanence
Spin Speed selection knob: With the models that contain a
speed selection knob, you can spin your laundries until 1200 rpm
by using this knob. Your machine will not spin over 800 rpm in
the synthetic programs and over 600 rpm in the woolen pro-
grams in order to protect your laundries. If you want to take out
your laundries without spinning, turn the speed selection knob to
“No Spin” position.
Pressing “On/Off”: You can make the machine ready for
program selection by pressing the “On /off” button. When “On/
Off” button is pressed, “Door” LED is on meaning that “door can
be opened”. To turn off the machine, press the “On/Off” button
again.Pressing the “On/Off” button never means that the program
is started.You must press “Start/Pause/Cancel” button in order
the machine starts its program.
Child-proof lock: “This machine is equipped with a child lock
in order to prevent the program flow to be affected when the
buttons are pressed during washing cycles. In order to enable
the child lock, press and keep pressed the 1st and 2nd auxiliary
function buttons from the left at the same
time for 3 seconds. The light of the 1st
auxiliary function button will flash continu-
ously. After the program completes, it
is necessary to disable the child lock in
order to initiate a new program or interfere
the program. Therefore, when the same
buttons are pressed for 3 seconds, light of
the second auxiliary function will go off.
Function Selection: Depending on the selected program, the
selectable auxiliary functions are selected by pressing the each
function’s button. The light of the selected function comes on.
Since it is not possible to select some of the auxiliary func-
tions together, one of them becomes off when the other one is
selected.
Program Progress
After the machine starts to operate, the related light in the program
follow-up indicator comes on according to the selected program.
When a step is complete, the light of the previous step goes off
and the light of the related step comes on. When On/Off button is
pressed, the “Door” light comes on.After the washing program is
selected, “Washing” light on the program follow-up indicator comes
on when the “Start/Pause/Cancel” button is pressed.When the
program ends “End” light comes on. After the program is complete,
the
machine will not allow you to open the door for a while for your
safety. If you want to open the door meanwhile, the door will not
open and the “Door” light will flash. After the door lock is deactivat-
ed the “Door” and “End” lights will come on. Now you can open the
front door. You can switch your machine in to the “Pause” mode by
pressing the “Start/Pause/Cancel” button while your machine is
operating.In this case, “Start/Pause/Cancel” light will flash. You can
make some changes in the program settings in the Pause mode
(See. Changing the Program) and you may also benefit from the
laundry addition function if the “Pause” mode is selected at a
suitable step of the program (See. Laundry addition function).
In
order to return to the “Washing” mode from the “Pause” mode,
you need to press the “Start/Pause/Cancel” button again. In this
case, “Start/Pause/Cancel” light will flash and your machine will
resume its program.
Changing Program
Even if a new program is selected by changing the position of
program selection knob while your machine is operating, the first
selected program continues to run.In order to change the wash-
ing program, the ongoing program should be cancelled. (See.
Cancelling a program)
In order to change the auxiliary functions while your machine is
operating, you can make any desired changes after pressing the
“Start/Pause/Cancel” button.
If you want to change the spin speed while your machine is
operating, press the “Start/Pause/Cancel” button, select the spin
speed and press the “Start/Pause/Cancel” button again.
Adding laundry
If you want to add laundry to your machine after the washing
program starts, switch the machine to pause mode by pressing
“Start/Pause/Cancel” button. If the water level in the machine
is suitable, the “Door” light on the program follow-up indicator
comes on approximately 2 minutes later and you can open the
door and add laundry. If the “Door” light is not
continuously on at the end of this period, the water level in the
machine is not suitable and you can not add laundry. You can
resume the program by pressing “Start/Pause/Cancel” button
again.
Canceling a Program
In order to cancel the selected program, “Start/Pause/Cancel”
button is pressed for 3 seconds and machine starts to drain at
the end of this time. Meanwhile, “Washing” and “End” lights are
on. After the drainage process completes “Start/Pause/Cancel”
and “Washing” lights are off. “Door” light starts to flash. When the
“Door” light is on continuously, the door
can be opened and a new program can
be selected. You can start a program
by selecting a new program.
The selected program continues to run
even if the position of program selection
knob is changed while your machine is
operating. In order to change the wash-
ing program, a new program can be
selected and started after “Cancelling a program” by pressing the
“Start/Pause/Cancel” button for 3 seconds as described above.
End of Program
When the program ends “End” light on the program follow-up
indicator comes on. “End” and “Door” lights come on within two
minutes after the door is opened, the machine becomes ready for
the next washing. If any of the buttons is pressed or the posi-
tion of the selection knob is changed when the machine is at the
end of a program, “End” light goes off and only the “Door” light
remains on. Meanwhile, if the door is still locked, the “Door” light
flashes until the door is opened. To turn the machine off, press
the “On/Off” button.
Emptying Laundry
Your machine stops automatically when the program ends. Turn
off the taps. Grab and pull the handle to open the door. Press
“On/Off” button to turn off your machine. After you take the laun-
dries out, leave the front door open and ventilate the inside of the
machine. Check the inside of the bellows and wipe it.