Filter
Top Products
29 - EN
Auxiliary function
Low temperature
This function allows for drying at lower
temperatures and therefore saves energy.
Warning LED will light up when you select the
function.
C You must use this function when you dry
your synthetic or delicate laundry.
Warning indicators
C Warning indicators may differ according to
the model of your machine.
Filter cleaning
A warning LED will light up to remind filter
cleaning after the program finishes.
C If the filter cleaning warning LED lights up
continuously, please refer to, “Solution
suggestions for problems”.
Starting the Program
1. Press “Start/Pause/Cancel” button to start
the program.
2. “Start/Pause/Cancel” button will light up to
indicate that the program has started.
Timer follow-up indicator
One of the lamps is on as far as program runs
and shows the approximate remaining time.
C LEDs on the timer follow-up indicator will also
flash when the child-proof lock is activated.
A If more than one LED light up or flash
concurrently, it means there is malfunctioning
or a failure (please see, Solution suggestions
for problems).
Changing the program after the
program has started
You can use this feature to dry your laundry in a
different program after your machine has started
to run.
For example;
Press and hold the “Start/Pause/Cancel” button
for about 3 seconds to select “80” minutes
program instead of “60” minutes program.
Select the “80” minutes program by rotating the
program knob.
Press “Start/Pause/Cancel” button to start the
program.
C The program which is selected first will
go on even if the program selection button
is moved and another program mode is
selected while the machine is operating. You
must cancel the ongoing program in order to
change the drying program. (See, Ending the
program through canceling)
Adding/removing laundry in standby
mode
In order to add or take out laundry after the
start-up of the program;
1. Press the “Start/Pause/Cancel” button to
switch the machine to “Pause” mode. Drying
process will stop.
2. Open the door at Pause position and close it
again after adding or taking out laundry.
3. Press “Start/Pause/Cancel” button to start the
program.
C Any laundry added after the drying process
was started may cause the already dried
clothes in the machine intermingle with wet
clothes and the result will be wet laundry after
the drying process is over.
C Laundry may be added or taken out as much
as desired during a drying process, but as
this process will interrupt drying continuously,
it will extend the program duration and
increase energy consumption. Therefore, it
is recommended to add laundry before the
drying program is started.
Child-proof lock
There is a childproof lock to prevent any
program interruption due to the pressing of keys
while the program is on. The loading door and
all keys except the “On/Off” key on the panel are
deactivated when the child-proof lock is active.
In order to activate the childproof lock, press
on the “Start/Pause/Cancel” and “Low
temperature” buttons simultaneously for 3
seconds.
To start a new program after the program is
over or to interrupt the program, the childproof
lock should be deactivated. To deactivate the
childproof lock, press the same buttons for 3
sec.
COne of the LEDs on the program follow-up
indicator starts flashing when the child-proof
lock is activated.
C Child-proof lock is deactivated when the
machine is restarted by pressing the On/Off
button.
Ending the program through canceling
The program which is selected first will keep
on going even if the position of the program
selection button is changed. A new program
can be selected and started after “Program
cancel” is activated in order to change the drying
program.
To cancel any selected program;
• Press “Start/Pause/Cancel” button for about
a duration of 3 seconds. The “Filter cleaning”
and “Water tank” warning LEDs as well as the
“0” warning LED on the program follow-up
indicator will light up at the end of this period