Filter
Top Products
8 Maytag Co. 113062-17
Provisions for adequate air supply must be provided as noted
in this manual (refer to Fresh Air Supply Requirements
section).
Clearance provisions must be made from noncombustible
construction as noted in this manual (refer to Dryer Enclosure
Requirements section).
Even though a 12-inch clearance is acceptable, it is
recommended that the rear of the dryer be positioned
approximately 2 feet away from the nearest obstruction, i.e.,
wall, for ease of installation, maintenance, and service. (Refer
to the illustration below.)
Provisions must be made for adequate clearances for
servicing and for operation as noted in this manual (refer to
Dryer Enclosure Requirements section).
Dryer must be exhausted to the outdoors in an area where
correct exhaust venting can be achieved as noted in this
manual (refer to Exhaust Requirements section).
Dryer must be located in an area where correct exhaust venting
can be achieved as noted in this manual (refer to Exhaust
Requirements section).
The dryer must be installed with a proper exhaust duct
connection to the outside.
The dryer must be installed with provisions for adequate
combustion and make-up air supply.
CAUTION: This dryer produces combustible lint and must
be exhausted to the outdoors. Every six months, inspect
the exhaust ducting and remove any lint build up.
IMPORTANT: Dryer must be installed in a location/
environment, which the ambient temperature remains
between 40° F (4.44° C) and 130° F (54.44° C).
IMPORTANT: Dryer should be located where a minimum
amount of exhaust duct will be necessary.
Installation Procedures _______________
Installation should be performed by competent technicians
in accordance with local and state codes. In the absence of
these codes, the installation must conform to applicable
American National Standards: ANSI Z223.1-LATEST EDITION
(National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST
EDITION (National Electrical Code) or in Canada, the
installation must conform to applicable Canadian Standards:
CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-
M91 (L.P. Gas) or LATEST EDITION (for General Installation
and Gas Plumbing) or Canadian Electrical Codes Parts 1 &
2 CSA C22.1-1990 or LATEST EDITION (for Electrical
Connections).
Unpacking/Setting Up _________________
Remove protective shipping material (i.e., plastic wrap and
optional shipping box) from dryer.
NOTE: The access keys for the service doors are included
in the information packet shipped in the tumbler. These
keys should be removed and put in a safe place yet made
accessible because some will be needed throughout
various phases in the installation of the dryer.
Dryers are shipped with a coin box and coin box faceplate
only. The coin box lock is not included and must be purchased
elsewhere or the lock can be ordered as a parts order from
the manufacturer.
The dryer can be moved to its final location while still attached
to the skid or with the skid removed. To unskid the dryer,
locate and remove the four bolts securing the base of the
dryer to the wooden skid. Two are at the rear of the base, and
two are located in the front. Once the bolts are removed,
slide the dryer off the skid.
With the skid removed, to make it easier to slide the dryer into
its final position, slightly lower all four leveling legs, so that
the dryer will slide on the legs instead of the base frame. The
dryer is equipped with four leveling legs, one at each corner
of the dryer base. The hex head adjustment bolts for the two
front leveling legs are located directly behind the lower access
door, and the rear two adjustments are directly behind the
lower rear back (guard) panel.
Location of the Dryer _________________
Before installing the dryer, be sure the location conforms to
local codes and ordinances. In the absence of such codes
or ordinances the location must conform with the National
Fuel Gas Code ANSI.Z223.1 LATEST EDITION, or in Canada,
the installation must conform to applicable Canadian
Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/
CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General
Installation and Gas Plumbing).
The dryer must be installed on a sound level floor capable of
supporting its weight. Carpeting must be removed from the
floor area that the dryer is to rest on.
IMPORTANT: “The dryer must be installed on
noncombustible floors only.”
The dryer must not be installed or stored in an area where it
will be exposed to water or weather.
The dryer is for use in noncombustible locations.