Filter
Top Products
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
F232226
14
Control Test
Warm fill to low water level Display flashes “bFIL”/“LO” (WASH LED on), no agitation
Outputs: Motor OFF, Drain closed, hot fill on, cold fill on
Pause after reaching low water
level
Display shows “LO” (no flashing), LOW water level dot ON, no agitation (keypad WASH
LED on); pauses until operator presses ^ keypad
Outputs: Motor OFF, Drain closed
Drain (can advance to next step
by pressing ^ keypad here)
Display shows “drAI”, no agitation (keypad WASH LED on)
Outputs: Motor OFF, Drain open
Cold fill to medium level Display flashes “CFIL”/“
nEd” (keypad WASH LED on), no agitation.
Outputs: Motor OFF, Drain closed, cold fill on
Pause after reaching medium
water level
Display shows “
nEd” (no flashing), LOW and MEDIUM water level dots ON no agitation
(keypad WASH LED on); pauses until operator presses ^ keypad
Outputs: Motor OFF, Drain closed
Hot fill to high level Display flashes “HFIL”/“HI” (keypad WASH LED on), no agitation.
Outputs: Motor OFF, Drain closed, hot fill on
Pause after reaching high water
level
Display shows “HI” (no flashing), LOW, MEDIUM, and HIGH water level dots ON, no
agitation (keypad WASH LED on); pauses until operator presses ^ keypad
Outputs: Motor OFF, Drain closed
Heat to 110°F (45°C)
SKIPS THIS STEP
if machine
does not have heat capability
(“noHt” selected in Setup
Mode)
Display flashes “HEAt” and the temperature inside the machine while agitating in forward
and reverse; continues until temperature reaches 110°F (45°C), then advances to next step.
(keypad WASH LED on)
Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 and
repeats; Drain closed; Heat ON UNTIL 110°F (45°C) reached
Extra supply / fill spare –
5 seconds (depends on setup)
Display flashes ‘ESUP’ / ‘EFIL’ (keypad RINSE LED on)
Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 and
repeats; Drain closed; ‘AF’ output ON.
Supply 1: 5 seconds (Heat
signal also on (IF at least low
water level – verifies output
even if not heated model)
Display shows ‘SUP1’ (keypad WASH LED on)
Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 and
repeats; Drain closed; Supply 1 ON, HT ON, cold fill ON
Supply 2: 5 seconds (Heat on
also)
Display shows ‘SUP2’ (keypad ADD BLEACH LED on)
Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 and
repeats; Drain closed; Supply 2 ON, HT ON, cold fill ON
Supply 3: 5 seconds (Heat on
also)
Display shows ‘SUP3’ (keypad RINSE LED on)
Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 and
repeats; Drain closed; Supply 3 ON, HT ON, cold fill ON
Supply 4: 5 seconds Display shows ‘SUP4’ (keypad RINSE LED on)
Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 and
repeats; Drain closed; Supply 4 ON, cold fill ON
Pause 5 seconds, then Forward
wash speed – 60 seconds
Display shows ‘For’
Outputs: Motor operates wash speed forward; drain closed
Table 5 (Continued)