Filter
Top Products
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
11
F232226
Temperature Controlled Fill
Display shows temperature in degrees F or C.
Display will show degrees F if configured for “FAr”
in Setup Mode, or degrees C if configured for
“CEL” in Setup Mode. Range is 75°F to 200°F, or
00F (no heat for segment), or 25°C to 93°C, or 00C
(no heat for segment).
Press the ∧ keypad to increase, or ∨ keypad to
decrease temperature in one-degree increments. The
control will energize heat and pause cycle timing for
up to 40 minutes until the programmed temperature is
first reached.
NOTE: If temperature not reached after
40 minutes, control resumes cycle.
After cycle resumes, control will attempt to maintain
programmed temperature if it senses water in the
machine.
If display shows “drAI”/“nodr” during segment
programming, a drain step option can be selected.
Select “drAI” for a drain step followed by an optional
spin. Select “nodr” for no drain step. The machine will
proceed directly to the next segment if “nodr”. Change
the selection by pressing the ∧ or ∨ keypad. Press
START to continue.
If “drAI” is selected (or if your model does not provide
the option of selecting “drAI”/“nodr”), the display will
show “SPIn” one second, “tI
nE” one second, and then
the time for spin: “00” (no spin) or 60-240 seconds.
Change the selection by pressing the ∧ or ∨ keypad.
Press START to continue.
Rinse 1 – Rinse 6
NOTE: Programming a time other than “00” for
this step will make the RINSE indicator LED light
while this step is running, but not in Program
Mode.
The main display shows “rIN1” indicating you are in
the Rinse segment (number will represent Rinse cycle
selected 1-6). Press START keypad. Display shows the
time for agitation during the step: “00” (skips
segment) or 2-30 minutes. This is the time after the fill
and before the drain and does not include spin time.
Press the ∧ or ∨ keypad to alter the selection, or the
START keypad to continue.
Display shows “CFIL”, “HFIL”, “bFIL” (for cold, hot,
warm [both]) or “AFIL”. Press the ∧ or ∨ keypad to
alter the selection, or the START keypad to continue.
Display shows “LO”, “
nEd”, or “HI” for low, medium,
or high water level, respectively. Press the ∧ or ∨
keypad to alter the selection, or the START keypad to
continue.
Display shows “SUP0”, “SUP1”, “SUP2”, “SUP3”,
“SUP4”, “SUP5”, “SUP6”, or “SUP7” indicating no
supply, supply 1, supply 2, supply 3, supply 4, supply
5 (supply 1 and supply 2 together), supply 6, or supply
7 (supply 3 and supply 4 together). Press the ∧ or
∨ keypad to alter the selection, or the START keypad
to continue.
NOTE: “SUP5” and “SUP6” appear ONLY if
control is configured for “SUP5” (spare mode set
up to operate as an EXTRA supply signal for
external chemical) in Setup Mode. If the alternate
function for the spare output is selected (“AFIL”),
the output will function as an additional fill valve
signal with a programmable water level. In this
case, extra supply function would NOT be
available.
If programmed for “SUP2”, the ADD BLEACH
indicator LED light turns on and the buzzer sounds
while supply 2 is on.
Press the ∧ or ∨ keypad to alter the selection or
START keypad to continue.