Filter
Top Products
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
F232224
14
Temperature Controlled Fill
17. Display shows temperature in degrees F or C.
Display will show degrees F if configured for
“FAr” in SETUP Mode, or degrees C if
configured for “CEL” in SETUP Mode. Range is
75°F to 200°F, or 00F (no heat for segment), or
25°C to 93°C, or 00C (no heat for segment).
18. Press the ∧ keypad to increase, or ∨ keypad to
decrease temperature in one-degree increments.
The control will energize heat and pause cycle timing
for up to 40 minutes until the programmed
temperature is first reached.
NOTE: If temperature not reached after
40 minutes, control resumes cycle.
After cycle resumes, control will attempt to maintain
programmed temperature if it senses water in the
machine.
19. If display shows “drAI”/“nodr” during segment
programming, a drain step option can be selected.
Select “drAI” for a drain step followed by an
optional spin. Select “nodr” for no drain step.
NOTE: The machine will proceed directly to the
next segment if “nodr”.
20. Change the selection by pressing the ∧ or ∨
keypad.
21. Press START to continue.
22. If “drAI” is selected (or if your model does not
provide the option of selecting “drAI”/“nodr”),
the display will show “SPIn” one second, “tI
nE”
one second, and then the time for spin: “00” (no
spin) or 60-240 seconds.
23. Change the selection by pressing the ∧ or ∨
keypad.
24. Press START to continue.
Rinse 1 – Rinse 6
NOTE: Programming a time other than “00” for
this step will make the RINSE indicator LED light
while this step is running, but not in PROGRAM
Mode.
25. The main display shows “rIN1” indicating you
are in the Rinse segment (number will represent
Rinse cycle selected 1-6).
26. Press START keypad. Display shows the time for
agitation during the step: “00” (skips segment) or
2-30 minutes.
NOTE: This is the time after the fill and before the
drain and does not include spin time.
27. Press the ∧ or ∨ keypad to alter the selection.
28. Press the START keypad to continue.
29. Display shows “CFIL”, “HFIL”, “bFIL” (for
cold, hot, warm [both]) or “AFIL”.
30. Press the ∧ or ∨ keypad to alter the selection.
31. Press the START keypad to continue.
NOTE: Auxiliary Fill (“AFIL”) possible only if
configured for “AFIL” in SETUP Mode. If
configured, auxiliary fills can be programmed to
low, medium, or high water level in cycle step.
32. Display shows “LO”, “
nEd”, or “HI” for low,
medium, or high water level, respectively.
33. Press the ∧ or ∨ keypad to alter the selection.
34. Press the START keypad to continue.
35. Display shows “SUP0”, “SUP1”, “SUP2”,
“SUP3”, “SUP4”, “SUP5”, “SUP6” or “SUP7”.
Refer to Table 3 for operation of each supply
selection.
36. Press the ∧ or ∨ keypad to alter the selection.
37. Press the START keypad to continue.
NOTE: “SUP5” and “SUP6” appear ONLY if
control is configured for “SUP5” in SETUP Mode.
If the alternate function is selected (“AFIL”), the
output will function as an additional fill valve
signal with a programmable water level. In this
case, the extra supply function would NOT be
available.
NOTE: If programmed for “SUP2”, the ADD
BLEACH indicator LED light turns on and the
buzzer sounds, if programmed, while supply 2 is
on.