4 © Titan Tool Inc. All rights reserved.
Table of Contents
Safety Precautions ................................................................2-3
Grounding Instructions ........................................................ 3
Gasoline Engine Safety ....................................................... 3
Specications ........................................................................... 4
Introduction ...............................................................................5
Operation ...................................................................................5
Fueling................................................................................. 5
Operating the Swing Cart .................................................... 6
Setup ................................................................................... 6
Preparing to Paint................................................................ 8
Painting ............................................................................... 8
Pressure Relief Procedure .................................................. 9
Cleanup ..................................................................................... 9
Cleaning a Clogged Tip ..................................................... 10
Maintenance ............................................................................ 10
Daily Maintenance ............................................................. 10
Maintaining the Filter Assembly ........................................ 11
Maintaining the Hydraulic System ..................................... 11
Maintaining the Fluid Section ............................................ 11
Basic Engine Maintenance (gas engine) ........................... 12
Replacing the Motor Brushes (electric motor) ................... 12
Troubleshooting ..................................................................... 13
Airless Gun ........................................................................ 13
Fluid Section...................................................................... 13
Hydraulic Motor ................................................................. 14
Spray Patterns................................................................... 15
Parts Lists and Service Instructions .................................... 20
Main Assembly .................................................................. 20
Cart Assembly ................................................................... 21
Hydraulic Motor ................................................................. 22
Fluid Section...................................................................... 24
Hydraulic System .............................................................. 26
Belt Guard Assembly......................................................... 27
Gas Convertokit................................................................. 28
DC— Electric Convertokit.................................................. 28
Electric Convertokit, 230V ................................................. 29
Bleed Valve Assembly....................................................... 29
Filter Assembly .................................................................. 30
Heavy Duty Outlet Assembly (optional)............................. 31
Heavy Duty Bleed Valve Assembly (optional) ................... 31
Gun Manifold Assemblies (optional).................................. 32
SAE O-Ring Fitting Installation .......................................... 34
Accessories and Service Kits ............................................... 34
Airless Tip Selection .......................................................... 34
Warranty .................................................................................. 36
Specications
Gas Sprayer
Gallons per minute (GPM) ............. 2.35 (8.9 LPM)
Cycle rate per gallon......................56 (15 cycles/liter)
Maximum tip sizes .........................1 gun = .050”
2 guns = .033”
3 guns = .023”
4 guns = .019”
Maximum pressure ........................3600 PSI (24.8 MPa)
Power .........................................Honda 163cc, 4.8 HP,
4-stroke, single cylinder,
overhead valve engine w/oil
alert
Fuel capacity .................................0.83 US gallons
(approx. 3.5 hours run time)
Halogenated solvent compatible ...Yes
Weight .........................................139 lbs. (67.6 kg.)
Inlet paint lter ...............................10 mesh “Rock Catcher”
Outlet paint lter ............................50 mesh, 18 in.
2
Pump inlet......................................1” NPT(F)
Pump outlet ...................................1/2” NPT(F) to paint lter
Paint lter hose connections..........3/8” NPS(M)
3/8” NPT(F) (plugged)
1/4” NPT (plugged)
Dimensions .................................... 43” L (109 cm) x
26” W (66 cm) x
35” H (89 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, PTFE, thiokol
impregnated leather, ultra high molecular weight polyethylene.
Electric Sprayer (with optional Convertokit)
Gallons per minute (GPM) ............. 1.25 (4.7 LPM)
Cycle rate per gallon......................55 (14.5 cycles/liter)
Maximum tip sizes .........................1 gun = .036”
2 guns = .033”
3 guns = .023”
4 guns = .019”
Maximum pressure ........................3600 psi (24.8 MPa)
Power .........................................2 HP DC Motor, 115V 15.5A,
overload protected
Halogenated solvent compatible ...Yes
Weight .........................................165 lbs. (74.8 kg.)
Inlet paint lter ...............................10 mesh “Rock Catcher”
Outlet paint lter ............................50 mesh, 18 in.
2
Pump inlet......................................1” NPT(F)
Pump outlet ...................................1/2” NPT(F) to paint lter
Paint lter hose connections..........3/8” NPS(M)
3/8” NPT(F) (plugged)
1/4” NPT (plugged)
Dimensions .................................... 43” L (109 cm) x
26” W (66 cm) x
35” H (89 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, PTFE, thiokol
impregnated leather, ultra high molecular weight polyethylene.
