ENGLISH
22
BASIC
CONNECTIONS
BASIC OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADVANCED
CONNECTIONS
a RS-232C
Connect an external control device or other device for
servicing. (Use a straight cable for the connection.)
s DC OUT (DC TRIGGER)
External devices can be controlled from the unit
by connecting them to the DC OUT terminal (12 V
44mA max).
GND
+12V
d FLASHER IN
This unit can be controlled by connecting a control
box or other control device to this unit.
GND
Signal
R
R
L
L
R
L
L
R
AUDIO
INPUT
INPUT
MONITOR OUT
C
B
/
Y
VCR OUT
VCR IN
(
3
)
TV
(
1
)
DVD
(
2
)
DSS
(
4
)
S-VIDEO
VIDEO
OUTPUT 2
OUTPUT 1
INPUT 3
(
VCR
)
INPUT 2
(
DVD
)
INPUT 1
(
TV
)
FM
(
75
Ω
)
GND
AM
ANTENNA
R
SR
C
SW
SBR
SL
SBL
L
PRE OUT
ON
RS-232C
SPEAKER C
OFF
CENTER
SURROUND
FRONT A
FRONT B
SURROUND BACK
SPEAKER C/
ZONE SPEAKER A
R
L
CD/CDR
OUT
IN
OUT
IN
TAP E
TV
DSS
VCR
DVD
OUT
OUT
IN
REMOTE CONT.
IN
OUT
OUT
3
1
4
DIGITAL IN
5
2
REC/ZONE B
DIGITAL
DC OUT
FLASHER IN
7.1CH INPUT
(
AUX 2
)
SL
C
L
SBL
R
SR
SW
SBR
ZONE A
SPEAKER SYSTEMS
FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS
FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS
FRONT A + B : 8 OHMS
SWITCHED
1.25A 150W
UNSWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
DC OUT
FLASHER IN
RS-232C
a
CONNECTING OTHER EQUIPMENT
L
OUTPUT 2
OUTPUT 1
INPUT 2
(
DVD
)
INPUT 3
(
VCR
)
INPUT 1
(
TV
)
COMPONENT
VIDEO
MONITOR OUT
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
VCR OUT
VCR IN
(
3
)
VD
(
2
)
DSS
(
4
)
UND BACK
AKER C/
SPEAKER A
REMOTE CONT.
IN
OUT
OUT
3
DIGITAL IN
5
2
REC/ZONE B
DIGITAL
DC OUT
FLASHER IN
MODEL NO. SR6003
SWITCHED
1.25A 150W
UNSWITCHED
1.25A 150W
AC IN
AC OUTLETS
120V 60Hz
SIRIUS
REMOTE CONT.
IN
OUT
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
CONNECTING THE REMOTE CONTROL JACKS
DVD playerCD recorder
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
control only at the unit. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the back of
other units (not the SR6003) to “EXT.” (EXTERNAL)
to use this feature.
CD player
OPTION
w
Whenever external infrared sensors or similar devices
are connected to RC-5 IN of the unit, be sure to
always disable operation of the infrared sensor on the
unit by using the following procedure.
1.
Hold down the SURROUND MODE button
and the MENU button on the front panel at the
same time for fi ve seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press the CURSOR buttons (1, 2) to change
this to “IR=DISABLE”.
4.
Press the ENTER button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
