Filter
Top Products
Select the required programme by turning the
programme selector dial (1)
Turn the programme selector dial to the required pro-
gramme. The washing machine will automatically select
the maximum spin value provided for the programme you
have chosen. You can change this value by pressing the
corresponding button. The green pilot light of the button
6 starts to flash.
The selector dial can be turned either clockwise or coun-
terclockwise. Turn to position « O » to reset programme/
Switching the machine off.
At the end of the programme the selector dial must be
turned to position O, to switch the machine off.
Caution! If you turn the programme selector dial to
another programme when the machine is working,
the red pilot light of button 6 will blink 3 times to indicate
a wrong selection. The machine will not perform the new
selected programme.
Select the required temperature by turning the
temperature selector dial (2)
Turn clockwise this dial to select the more convenient to
your laundry washing temperature.
Select the available options by pressing buttons 3,
4 and 5
Depending on the programme, different functions can be
combined. These must be selected after choosing the de-
sired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 6 flashes for 3 times.
For the compatibility among the washing pro-
grammes and the options see chapter «Washing
Programmes».
Start the programme by pressing button 6
To start the selected programme, press the button 6 , the
corresponding green pilot light stops blinking. The ap-
pliance starts operating and the only pilot light corre-
sponding to the running phase stays on.
To interrupt a programme which is running, press the
button 6 : the corresponding green pilot light starts blink-
ing.
To restart the programme from the point at which it was
interrupted, press the button 6 again .
If an incorrect option is selected, the red pilot light of the
button 6 blinks 3 times.
Altering an option or a running programme
It is possible to change some options before the pro-
gramme carries them out.
Before you make any change, you must PAUSE the ap-
pliance by pressing the button 6 .
Changing a running programme is possible only by re-
setting it. Turn the programme selector dial to O and then
to the new programme position. Start the new programme
by pressing the button 6 again. The washing water in the
tub will be not emptied out.
Interrupting a programme
Press the button 6 to interrupt a programme which is
running, the corresponding green pilot light starts blink-
ing.
Press the button again to restart the programme.
Cancelling a programme
Turn the selector dial to to cancel a programme which
is running. Now you can select a new programme.
Opening the door
After the programme has started the door is locked. If, for
any reason, you need to open it, set firstly the machine to
PAUSE by pressing the button 6 . After a few minutes it
will be possible to open the door.
If the door remains locked, this means that the machine
is already heating or that the water level is too high. In
any case, do not try to force the door!
If you cannot open the door but you need to open it you
have to switch the machine off by turning the selector dial
to O . After a few minutes the door can be opened (pay
attention to the water level and temperature!) .
After closing the door, it is necessary to select the pro-
gramme and options again and to press button 6 .
At the end of the programme
The machine stops automatically. The pilot light of button
6 and the pilot light corresponding to the just finished
washing phase go off. The light 7.3 illuminates.
If a programme or an option that ends with water left in
the tub has been selected, the light 7.3 illuminates but the
door remains locked to indicate that the water must be
emptied out before opening the door.
Follow the below instructions to empty out the water:
1. Turn the programme selector dial to O .
2. Select the draining or spinning programme.
7