Filter
Top Products
EN
9
Signals for successive refilling:
Once, at the end of a cycle, the level of detergent/fabric
softener falls below the level required for a successive
wash cycle, the display will visualise the relative
messages "At end of cycle refill detergent" or "At end
of cycle refill softener" or "At end of cycle refill
tanks". If the tanks are not filled, the successive wash
cycles in Auto Dose System will be carried out without
any intake of detergent.
We suggest adding detergent and fabric softener
ONLY after the machine's signal.
NEVER mix two different detergents; always clean out
the tank before adding a new type of detergent (refer to
"Cleaning cycle set by the user").
Using the "Auto Dose System"
If the compartments have been filled with detergent and
fabric softener, you may start using the machine (refer
to "Running a wash cycle").
Powder detergents for pre-washing and powder
additives may only be used in the traditional mode or
using the "Auto Dose System", by placing the additives
directly inside the drum, preferably in conjunction with
the "laundry ball".
Modifying pre-set parameters:
The machine automatically intakes detergent on the
basis of the selected programme, wash load and water
hardness. However, the amount of detergent/fabric
softener used may be modified.
button: press to increase, decrease and to exclude
detergent intake.
button: press to increase, decrease and to exclude
fabric softener intake.
The level of detergent/fabric softener suggested by the
machine is indicated by 3 bars.
Less than 3 bars indicates a lower level of detergent/
fabric softener compared to that suggested by the
machine, while more than 3 bars indicates a higher level
of detergent/fabric softener.
Cleaning the tanks:
Tank cleaning cycles can either be automatic or pre-set
by the user.
Automatic cleaning:
The washing machine carries out an automatic cleaning cycle
during the rinse cycle if the level of detergent that remains is
insufficient for carrying out a successive wash cycle.
Cleaning cycle set by the user:
Run the cleaning cycle (with empty drum) if you require
adding a different product to the previous one or if the
tanks have been incorrectly filled (e.g. fabric softener
has been erroneously poured into the detergent tank or
vice-versa). Press button
and hold for 5 sec. to
activate cleaning of the detergent tank, button
for
cleaning the fabric softener tank or button
for
cleaning both tanks. Keep pressing for a further 3 sec.
(the countdown "4-3-2-1" will appear in the top right
corner) until "CLEAN-GO" pops up.
The cleaning cycle lasts about 40' if the tanks are initially
empty; if not, the cycle will last longer. The icons
indicating that the tanks are empty will appear on the
display.
"Traditional" mode
Pull out the detergent dispenser drawer up to the first
stop point (see picture) then pour the amount of
detergent and other additives (e.g. bleach) required for a
single wash cycle directly into the dispenser.
1. pre-wash compartment:
use powder detergent only.
2. main wash
compartment: use powder
or liquid detergent. If the
latter is used, we
recommend pouring it into
the dispenser immediately
before starting the washing
machine and without
running a pre-wash cycle.
3. ! Do not pour anything in this compartment.
Tablet detergent or the relative "laundry ball" must be
added directly inside the drum. In this event, deactivate
the "Auto Dose System" (by pressing the
button until
the relative vertical bars disappear from the display).
Do not pour any fabric softener as the appropriate
quantity required for each wash cycle will be
automatically extracted.
To deactivate fabric softener intake, press the
button
until the vertical bars disappear from the display.
For wool and silk garments, we recommend using a
special detergent which must be poured directly into the
detergent dispenser (compartment 2).
Running the wash cycle:
Select the programme and the compatible options on
the basis of the required need and type of load.
3
1
2