Filter
Top Products
5019 312 10142
Whirlpool is a registered trademark of Whirlpool USA
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with standard IEC 60 456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the “Energy Label” refer to the programme “Cotton 60°C”.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
1. Load the machine, close the drum doors and
check that they are properly locked.
2. Add detergents and additives into the dispenser
to no more then the
“MAX”
level mark, as
follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Chlorine bleach
• Stain remover agents
• Anti-scale agents (if necessary)
3. Turn the
programme selector knob
to the
desired programme.
4. Turn the
temperature selector knob
to the
desired temperature.
5. Turn the
spin speed selector knob
to the
desired spin speed. If the spin speed “0” is
selected, the final spin is cancelled, but not the
intermediate spins. The programme ends with a
drain cycle.
Selecting or deselecting an option can be done at
any time during the programme. The option will
be applied as long as the corresponding
programme phase has not been executed yet.
“Eco” button
• The duration of the wash is extended and the max
temperature reduced to save up to 40% of energy
compared to a normal wash but maintaining good
washing results.
“Half Load” button
• Can be used for small loads and lightly soiled
laundry.
• Reduces the water consumption especially during
the rinses.
“Intensive Rinse” button
• One rinse cycle is added to ensure a more
intensive rinse.
• This option is particularly suitable for areas with
very soft water, washing baby linen and people
with detergents allergies.
CONSUMPTION DATA
Programme
Temperature Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton 90 5.0 63* 1.80 2:05
Cotton 60 5.0 59 0.95 2:05
Cotton 40 5.0 59 0.60 2:05
Daily Mixed 40 3.0 45 0.48 1:00
Synthetic 60 2.0 62 0.80 1:35
Synthetic 40 2.0 56 0.45 1:30
Delicate 40 1.5 63 0.45 0:50
Wool 40 1.0 63 0.45 0:40
Handwash 30 1.0 63 0.30 0:50
PREPARATION OF WASH CYCLE SELECT THE DESIRED OPTION
“Rinse Hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from fading.
• This option is particularly recommended for the
“Synthetic”, “Delicate” and “Daily Mixed”
programmes.
• This function is particularly useful if you want
to postpone spinning to a later time, or if you
want to drain only.
Note:
the programme selector knob stops on .
Appliance in “Rinse Hold”:
• Press the “Rinse Hold” button again: the
programme will terminate automatically with
the selected spin cycle.
• If you do not wish to spin the clothes, press the
“
On/Off
” button, turn the programme selector
knob to the “Drain” programme and press the
“
On/Off
” button again.
Turn on the tap and press the “
On/Off
” button. The
indicator light of the “
On/Off
” button lights up.
Note
: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
• The programme selector knob is in the Stop
position.
1. Press the “
On/Off
” button to switch off the
machine.
2. Cancel the options.
3. Turn the tap off.
4. Wait for the lid to unlock (about 1 minute).
5.
Open the lid and the drum doors and unload
the machine.
1. Switch off the machine by pressing the
“
On/Off
” button.
2. Select the new programme.
3.
Start programme by pressing the “
On/Off
”
button again.
If, for any reason, you wish to interrupt the
programme for a certain time and continue it later:
1. Press the “
On/Off
” button.
2. After the desired pause, press again the
“On/Off”
button.
1. Switch off the machine by pressing the
“
On/Off
” button.
2. Set the programme selector to “Drain”.
3. Press the “
On/Off
” button again to start the
“Drain” programme.
PROGRAMME START
END OF WASH CYCLE
CHANGE THE PROGRAMME DURING THE WASH
CYCLE
PAUSE/INTERRUPT A PROGRAMME
CANCEL PROGRAMME