Filter
Top Products
5019 301 01109
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton / Antibacterial 95 5.0 49** 1.90 2:00
Cotton 60 5.0 44 0.95 2:10
Cotton with “Eco”*** 60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Jeans 40 5.0 60 0.60 2:10
Synthetics 60 2.5 50** 0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool
40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Lingerie 30 1.0 45 0.50 0:36
CONSUMPTION DATA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash.
* The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the
lamp lights to show the the door can be opened.
As long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel (Reset)
a running programme before the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for
Use”; if the fault persists, contact our After Sales
Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap: if the indications still lights
up, refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned:
in the latter case refer to the Instructions for Use
(“Removing the Filter”).
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of options
are deselected automatically.
“Eco” button
• With modified temperature profile and a slightly
prologned washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Prewash”
button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause”
button lights up. The programme sequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme
time. Due to variations in load and temperature of
inlet water, the remaining time is newly calculated
in certain programme phases. If this is the case, an
animation appears on the time display.
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
• Do not use liquid detergent for the main wash
when activating the “Prewash” option.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics”
and “Daily load” programmes to make ironing
easier.
• Increases the water quantity and the clothes are
spun very gently.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
without pregressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
• If you select “Rinse hold” do not leave items to
soak for too long.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” lights in the programme
sequence indication is on. The indication lamp
next to the “Start/Pause” button blinks.
START DELAY
Add detergents as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. Turn the programme selector to the desired
programme and temperature.
2. The time display shows the duration of the
chosen programme (in hours and minutes), and
the “Start/Pause” indication lamp is blinking.
3. The indication lamp of the predefined spin speed
lights up.
Terminate the “Rinse hold” option:
• Press the “Start/Pause” button; the programme
will terminate automatically with the final spin
cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme and press the “Start/Pause” button.
“Variable spin”
button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
The “Reset” button cancels a programme before
the end.
• Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door
can be opened.
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
Do not use liquid detergent
when activating “Start delay” option.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay
time by 1 to 23 hours.
• Press the “Start/Pause” button.
The countdown of the delay time begins; the
“Start delay” indication lamp and the dot on the
display will keep blinking until the programme
starts.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining programme time.
• Once having pressed the “Start/Pause” button,
the number of hours preselected can be reduced
by pressing again the “Start delay” button.
To cancel the “Start delay”
...before you press the “Start/Pause” button:
• Turn the programme selector to another position
or press the “Reset” button.
...after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3 seconds
- the start delay time disappears from the time
display.