Filter
Top Products
Before you start... b;g;;i zt;g’;n~l
Check code requirements. Some codes
Protection from
do not permit or limit the installation of
weather: Do Not store
Check location where washer/
ordinances.
clothes dryers I” garages. closels.
or operate washer/
moblIe homes and quarters
drver below 32 F (some
dryer will be installed Proper
lnstollat~on IS vour resDonslbllitv
Make sure You hove’everythl~g
necessary for correct instollatlon
waler may remal” I”
washer) Proper
operation of dryer
cycles requires
temperatures above
45 F See Use & Care
Guide for Wlnterizlng’
information
Grounded electrical outlet
IS required (See “Electrlcol
requirements” )
Standpipe drain system needs
o two-inch diameter standplpe
with o m~n~rnum carry-away
copaclty of 17 gallons per
minute The top of the
stondplpe must be at least
34 Inches high and no
higher than 72 Inches
from the floor
Floor drain system
requires cz siphon
break, Part No
285320 ova~lable
from WhIrlpool
outhorlzed parts
dlstrlbutor
Dryer may be
exhausted from
the rear or left or
right side
Exhausting
throuqh the side
requlr&s Part No
3391335 (See
“Exhaust
requirements’
Panel B )
Water heater Set to
d&vcr 140 F
water
tc
the washer
Laundry tub drown
~. system: needs 01 leasi
Four-inch metal
exhaust duct is
required.
Fire Hazard
. DO Not use or store gasoline,
paint, thinners and other
flammable materials near
washer/dryer Fumes from such
materials could result in fire or
explosion.
. Never install washer/dryer up
against draperies or curtains or
on carpet. To do so may result
in a fire.
. Keep any and all items from
falling or collechng behind the
washer/dryer. Failure to do so
may result in a fire.
l
Replace all access panels
before operaiing washer/dryer.
Failure to do so may result in a
fire or electrical shock.
:no h,gher lhon 7i
mnches f’orr f,cor
/A
If u longer droln hose I!
needed drain hose
Port No 388423 onc
least 34 nches hlo” on j
Level floor: MaxImum slope
under washer:‘dryer - 1 Inch
rt Floor must be sturdy enough
o support washer/dryer weight wlIh
water and clothes of 500 pounos
SEE RECESSED AREA
INSTRUCTIONS ON
BACK COVER.
hose extenslo” kit Port
No 285442 ore
avolloble f!om
Electrical
requirements
Tools and
materials needed
for installation:
1 A three-wire. single phase, 1201
240.volt. &Hz, AC only, electrical
supply, with a fourth wire OS o
grounding wire, (or three-wre, 1201
20%volt electrical supply with o
fourth wire as o grounding wire if
specified on nameplate) is required
on 0 separate 30.ampere clrcult.
fused on both sides of the line. The
fourth (groundIngI conductor must
be ldentlfied by a green or green1
yellow cover and the neutral
conductor bv o white cover
(Time-delay fuse or circuit breaker is
recommended )
Electrical Shock Hazard
.Electrical ground IS requrred on
this product
-Improper connectjon of the
equipment-groundrng conduclor
can resull rn electrical shock
*Check with a qualrfred electrician
if you are in doubl OS to whether
the appliance is properly
grounded
l
Do Not modify the power supply
cord oluo. If it will not fit the outlet.
have.0 Goper outlet installed by
a qualified electrician. Modifying
the power supply cord plug
could result in electrical shock
-Use a new JO-ampere power
supply cord kit. Do Not reuse an
old power supply cord. Possible
electrical shock or fire hazard
could occur if old power supply
cord is used.
-Do Not use an extension cord
with this appliance. Such use
may result In 0 fire, electric01
shock or other personal injury
*Do Nol hove a fuse in the neutral
or grounding circuit Thus could
result In electrical shock.
large enougn so aryer
door co” open fully - c:t
least 90 (See bock
cover for Recessed
and closet ~nstollatlo”
lnstruct’ons and
Product Dimensions’
SEE RECESSED AREA
INSTRUCTIONS ON
BACK COVER.
It is the personal responslblllty of the
customer to contact o quaIllied
Installer to assure that the electrlcol
lnstallotlon IS adequate and I”
conformance with the National
ElectrIcal Code ANSl/NFPA 70 -latest
edition. and local codes and
ordinances
2 This washer/dryer is equipped wltk
o 30.amp-rated. four-wire, flexible-
type. power supply cord (pigtail)
and o 314”. U L.-listed strain relief.
(See Figure 1 1 Where local codes
permit,.it must be plugged Into o
mating. 30-amp receptacle (NEMA
Type 14.30R) (See figure 2.)
3 IF THE POWER SUPPLY CORD IS
REMOVED. THE WASHER/DRYER MUST
BE CONNECTED WITH lo-GAUGE
MINIMUM, COPPER WIRE ONLY (See
Panels F and G ‘“Alternate electrlcal
connection”, for detailed
Instructions )
4 The power supply cord (pigtall)
co” be removed and the appliance
con be connected directly to a”
Indlvldual. 30.ampere. fuse or circuit
breaker box through flexible.
armored or non-metallic sheathed.
lo-gouge minimum, copper cable
It IS the personal responsibility and
obligation of the customer to
Panel A