Filter
Top Products
FEATURES OF YOUR TURBO STEAM™ IRON
1. Covered Water Fill Hole
2. Wait / Ready Light
3. Electronic / Digital Display
4. Auto-Off Indicator
5. Steam On/Off Buttons
6. Fabric Select Buttons
7. Turbo Steam™ Button
8. Shot of Steam
®
Button /
Vertical Steam Button
9. Soft Grip Handle
10. Cord Lock™ Feature
11. Self-Clean Button
12. Translucent Water Reservoir
with Max/Refill Lines
13. Soleplate
14. Storage Strip™ Indicator
S
t
o
r
a
g
e
S
t
r
i
p
Cle
a
n
10
7
3
6
2
1
wait
ready
Toggle up to desired fabric
and wait for red light
to turn green.
4
8
9
12
11
13
14
5
Figure A
TO FILL THE WATER RESERVOIR
1. Make sure the iron is unplugged.
2. Lift the Water Fill Hole Cover.
3. Fill water cup with water. Pour water into iron
water reservoir. Do not fill water reservoir beyond
maximum fill level.
WARNING:
To prevent the risk of burns, be careful
when filling a hot iron with water. Hot metal parts, hot
water and steam can cause injuries.
SELECTING FABRIC SETTINGS
To select a fabric setting, press the Fabric Select buttons
(▲▼) until the desired fabric lights up (Figure A). The
Wait/Ready light will change from red to green when
the iron is ready to use.
NOTE:
When using the Steam Function, the iron will
automatically adjust the steam to match the fabric selec-
tion.
DRY IRONING
1. Plug the cord into a 120-Volt AC outlet.
2. Select Fabric Setting.
3. Press the Steam Off button.
NOTE:
While in the Steam Off (Dry) setting, you may
still use the Shot of Steam
®
feature or Turbo Steam
™
feature. Please make sure the water reservoir is at least
full to the Refill line.
TIP:
Refer to the Ironing Guide for the recommended
setting for your fabric.
STEAM IRONING
1. Follow the instructions for “To fill the Water Reservoir”.
2. Plug the cord into a 120-Volt AC outlet.
3. Select Fabric Setting.
4. When the green ready light turns on press the Steam
On button.
TIP:
Refer to the Ironing Guide for the recommended
setting for your fabric.
USING THE IRON’S SPECIAL FEATURES
TURBO STEAM
™
FEATURE
The Turbo Steam™ feature allows the iron to function as a powerful
garment steamer. It can provide continuous pulsating steam for up to
10 minutes and can be used horizontally or vertically. Turbo Steam is
ideal for steaming wrinkles out of delicate clothing, hanging garments
and draperies.
To use Turbo Steam™:
1. Fill the water reservoir to the max fill line.
2. Hold the iron, either horizontally and iron normally or
|vertically, close to but not touching the fabric or garment
to be steamed.
3. Using your free hand, keep the fabric pulled tight.
4. Press the Turbo Steam™ button once to turn the Turbo Steam™
feature on. Press the button again to turn it off. Turbo Steam will
not turn on while in SYN or SILK fabric settings.
5. The Turbo Steam™ feature will start once the iron reaches
maximum temperature.
IMPORTANT:
The Turbo Steam™ pump action may cause the
iron to vibrate slightly during use.
SHOT OF STEAM
®
/ VERTICAL STEAM FEATURE
The Shot of Steam
®
/ Vertical Steam feature provides an extra
burst of steam for deep penetration of stubborn wrinkles. You can
use this feature while Dry or Steam ironing, but the water reser-
voir must be above the Refill line.
To use the Shot of Steam
®
/ Vertical Steam Feature:
Place the iron on top of the wrinkle and press the Shot of Steam
®
button each time you would like an extra burst of steam. The Shot
of Steam
®
feature may be used continuously with just a
short pause between shots in both the horizontal and
vertical position.
WARNING:
To prevent the risk of burns, keep your hand away
from the area being steamed.
WARNING: DO NOT
steam garments while wearing them;
this may result in injuries.