Smeg AS62C Clothes Dryer User Manual


 
9 - EN
Auxiliary function
Low temperature
This function allows for drying at lower
temperatures and therefore saves energy.
WarningLEDwilllightupwhenyouselect
the function.
C Youmustusethisfunctionwhenyou
dry your synthetic or delicate laundry.
Warning indicators
C Warningindicatorsmaydiffer
according to the model of your machine.
Filter cleaning
AwarningLEDwilllightuptoremindfilter
cleaning after the program finishes.
C IfthefiltercleaningwarningLEDlights
upcontinuously,pleasereferto,“Solution
suggestionsforproblems”.
Water tank
AwarningLEDwilllightupattheendofthe
program or when the tank is full with water. The
machinestopsoperatingwhenthiswarningLED
lights up during a program running. To restart
the machine, please drain the water in the water
tank.Press“Start/Pause/Cancel”buttonto
start the program after you have emptied the
watertank.ThewarningLEDgoesoffandthe
program resumes operating.
Starting the Program
1.Press“Start/Pause/Cancel”buttontostartthe
program.
2.“Start/Pause/Cancel”buttonwilllightupto
indicate that the program has started.
Timer follow-up indicator
One of the lamps is on as far as program runs
and shows the approximate remaining time.
C LEDsonthetimerfollow-upindicator
will also flash when the child-proof lock is
activated.
C IfmorethanoneLEDlightuporflash
concurrently, it means there is malfunctioning
orafailure(pleasesee,Solutionsuggestionsfor
problems).
Changing the program after the
program has started
Youcanusethisfeaturetodryyourlaundryina
different program after your machine has started
to run.
Forexample;
Pressandholdthe“Start/Pause/Cancel”button
forabout3secondstoselect“80”minutes
programinsteadof“60”minutesprogram.
Selectthe“80”minutesprogrambyrotatingthe
program knob.
Press“Start/Pause/Cancel”buttontostartthe
program.
C The program which is selected first will
go on even if the program selection button
is moved and another program mode is
selectedwhilethemachineisoperating.You
must cancel the ongoing program in order to
changethedryingprogram.(See,Endingthe
program through canceling)
Adding/removing laundry in standby mode
Inordertoaddortakeoutlaundryafterthe
start-upoftheprogram;
1.Pressthe“Start/Pause/Cancel”buttonto
switchthemachineto“Pause”mode.Drying
process will stop.
2. Open the door at Pause position and close it
again after adding or taking out laundry.
3.Press“Start/Pause/Cancel”buttontostartthe
program.
C Anylaundryaddedafterthedrying
process was started may cause the already
dried clothes in the machine intermingle with
wet clothes and the result will be wet laundry
after the drying process is over.
C Laundry may be added or taken out
as much as desired during a drying process,
but as this process will interrupt drying
continuously, it will extend the program
duration and increase energy consumption.
Therefore, it is recommended to add laundry
before the drying program is started.
Child-proof lock
There is a childproof lock to prevent any
program interruption due to the pressing of
keys while the program is on. The loading
doorandallkeysexceptthe“On/Off”key
on the panel are deactivated when the child-
proof lock is active.
Inordertoactivatethechildprooflock,press
onthe“Start/Pause/Cancel”and“Low
temperature”buttonssimultaneouslyfor3
seconds.
To start a new program
after the program is
over or to interrupt
the program, the
childproof lock should be
deactivated. To deactivate
the childproof lock, press the same buttons for
3sec.
C OneoftheLEDsontheprogram
follow-up indicator starts flashing when the
child-proof lock is activated.
Ending the program through canceling
The program which is selected first will keep
on going even if the position of the program
selectionbuttonischanged.Anewprogramcan
beselectedandstartedafter“Programcancel”
is activated in order to change the drying