Filter
Top Products
TROUBLESHOOTING
Problem Possible cause Solution
Iron is leaking. DISTILLED WATER DO NOT use 100% pure distilled
water, use tap water. In very hard
water areas mix half tap water with
half distilled to reduce hardness; or
use inexpensive bottled spring water.
SOFTENED WATER If you experience leaks or spitting,
change to untreated tap water or
inexpensive bottled spring water.
DO NOT use 100% distilled water.
Is iron hot enough? Set thermostat to the (●●●) position.
Allow iron to heat up (light goes out)
before using steam.
Is auto-off activated?
Move iron or gently shake.
Overuse of burst of Allow more time between each
steam. burst.
Warm handle. Auto shut off is The shut off circuit in the handle
activated. produces a small amount of heat.
This is normal and will stop when iron
is switched on.
Iron won’t heat. Is iron plugged in? Check plug is in socket.
Thermostat set too Turn thermostat to a higher setting.
low?
Is auto-off activated?
Move iron or gently shake.
Indicator light This is normal. The light goes on and off showing
goes on and off. the thermostat is switching the heat on
and off to maintain the correct
temperature.
Iron does not Iron is not hot Set thermostat to the (●●●) position.
steam. enough. Always allow iron sufficient time to
heat up before activating the steam
control.
Steam valve is Move steam control forward and
clogged. back several times to clear blockage.
AFTER IRONING
˾
Unplug the iron. The variable steam control must be at the "max." setting in order to
empty the water from the tank.
˾
After emptying always push the variable steam control to the "min." setting and allow
the iron to cool down before storing away.
˾
Always store the iron on its heel (protects the soleplate).
˾
You should never store your iron on its soleplate even when it is cold.
SELF CLEANING
Vapodur Valve
The patented Vapodur valve ensures that the opening which allows the water to drip from
the water tank into the steam chamber of your iron remains unaffected by hard water
deposits. To ensure your iron continues to steam efficiently the valve MUST be opened and
closed a few times. This is done by moving the variable steam control from "min." to
"max." a few times each time you finish ironing.
Steam Chamber Cleaning Function (Depending on model)
This function allows loose mineral deposits and other impurities that build up inside the
iron to be flushed out. This type of self cleaning only needs to be carried out occasionally
and never more than once a month.
˾
Fill the iron with cold tap water and set variable steam to min.
˾
Stand on heel and plug in.
˾
Set thermostat dial to max. position.
˾
When the iron reaches the correct temperature, indicator light will go out, unplug iron.
˾
Hold iron horizontally over the sink with soleplate pointing away from body.
˾
Slide variable steam control completely over and hold in the section marked SELF CLEAN.
WARNING: Doing this will cause steam and hot water to be ejected from the
soleplate. Take all proper precautions and hold iron away from body.
˾
Move the iron gently back and forth and from side to side until all water has run
through.
˾
Carefully wipe all water and material from the soleplate with an old folded towel, as the
water and minerals can stain the soleplate (although this has no effect on glide or per-
formance).
WARNING: Iron and soleplate may still be hot, exercise care while wiping.
˾
Place iron on heel and leave to cool.
˾
IMPORTANT: Before using the iron after self cleaning, test steam and burst of steam on
an old towel or cloth to ensure all loose material has been removed from the iron.
WATER
Rowenta irons are designed to be used with REGULAR TAP WATER ( up to 12 grains of
hardness). If your water is harder than this, Rowenta recommends mixing half tap water
with half distilled water which reduces the hardness or using inexpensive spring water.
Never use 100 % distilled water since this can cause the iron to spit and leak.
Softened watrer: There are many types of household water softeners and the water from
many of them is perfectly acceptable for use in an iron. However, some types of softeners,
particularly those that use chemicals such as salt, can cause the iron to spit and leak during
use. If you experience this type of problem, we recommend that you try using inexpensive
bottled spring water or untreated tap water. Never use 100 % distilled water.
Dry ironing
0
Push the steam control to the
minimum setting.
When heated the temperature
control light will go off. You may
begin dry ironing
Cleaning the iron and soleplate
“
When cold and unplugged,
the iron can be cleaned with a
damp cloth and wiped dry.
Rowenta soleplates have excellent
non-stick properties and can be
simply wiped clean when cold.
In normal use a draggy coating may
build up on the soleplate (starch,
detergent buildup, burnt synthetic
fibers). This can be easily removed
by using the Rowenta Soleplate
Cleaning Kit or a quality hot iron
soleplate cleaner available at most
stores.
Do not use abrasive household
cleaners or abrasive cleaning pads.
Self Clean
ß
After ironing move the variable
steam control from "min." to
"max." several times. This ensures
the Vapodur valve remains free of
mineral build-up and the iron will
continue to steam. See self cleaning
section in instructions for additional
cleaning feature.
s
e
l
f
c
l
e
a
n
min
min
max
max
s
e
l
f
c
l
e
a
n
min
min
max
max
To prevent scratching of the sole-
plate, do not iron over sharp objects
(zippers etc.). Do not place the iron
on rough surfaces, e.g. metal iron
support, which may scratch the
soleplate.
6
Ensure that the iron is fully
heated (light goes out) before
using steam. Push the variable
steam control to the desired steam
setting. Temperature dial must be
set to the ●●● setting for steam.
s
e
l
f
c
l
e
a
n
min
min
max
max
4
The pilot light indicates that
the iron is heating. When
heated, the light will go off. It is
normal for the indicator light to go
on and off during use.
5
Before using the iron for the
first time or if the iron has not
been used for a few weeks, allow it
to steam for about 1 minute over
an old towel or cloth.
Steam Ironing
3
For steam ironing, turn the
temperature control dial to the
red setting (● ● ●). Delicate syn-
thetics should be dry ironed.
● synthetics
● ● silk, wool
● ● ● cotton, linen (steam setting)
min
Spray setting
7
Ensure there is water in the
tank. Moistening the fabric
with the spray will make wrinkle
removal easier. Press the spray
button down slowly for a jet or
quickly and strongly for a mist.
Do not spray silk, etc.
e
l
e
c
t
r
o
n
i
c