Filter
Top Products
6
■
Does the water level seem too low, or does the washer
appear to not fill completely?
The top of the agitator is much
higher than the highest water level. This is normal and
necessary for clothes to move freely.
■
Has a household fuse blown, or has a circuit breaker
tripped?
Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
■
Is the washer in a normal pause in the cycle?
The washer
pauses for about
2 minutes during certain cycles
.
Allow the
cycle to continue. Some cycles feature periods of agitation and
soak.
■
Is the washer overloaded?
Wash smaller loads.
■
Is the lid open?
The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
Washer won’t drain or spin
■
Is the drain hose clogged, or the end of the drain hose more
than 96" (244 cm) above the floor?
See the Installation
Instructions for proper installation of drain hose.
■
Is the lid open?
The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
■
Is there excessive sudsing?
Always measure detergent.
Follow manufacturer’s directions. If you have very soft water,
you might need to use less detergent.
Washer continues to fill or drain; cycle seems stuck
■
Is the top of drain hose lower than the water level in washer?
The top of the hose must be higher than the water level in the
washer for proper operation. See the Installation Instructions.
■
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe?
The drain hose should be loose yet fit
securely. Do not seal the drain hose with tape. The hose needs
an air gap. See the Installation Instructions.
Wash/Rinse temperature not what I selected
■
Are the hot and cold water inlet hoses reversed?
See the
Installation Instructions for more information. As your frequency
of loads washed increases, the water temperature may
decrease for hot and warm temperatures. This is normal.
Washer Results
Load too wet
■
Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).
■
Did you use a cold rinse?
Cold rinses leave loads wetter than
warm rinses. This is normal.
Residue or lint on load
■
Did you sort properly?
Sort lint givers (towels, chenille) from
lint takers (corduroy, synthetics). Also sort by color.
■
Did you overload the washer?
The wash load must be
balanced and not overloaded. Clothes should move freely. Lint
can be trapped in the load if overloaded. Wash smaller loads.
■
Did you select the correct water level?
The water level
should be correct for the load size. Clothes should move freely
in the water.
■
Did you use enough detergent?
Follow manufacturer’s
directions. Use enough detergent to hold the lint in the water.
■
Did you line dry your clothing?
If so, you can expect some lint
on the clothing.
■ Check the following:
Was paper or tissue left in the pockets?
Is your water colder than 60°F (15.6°C)? Wash water colder
than 60°F (15.6°C) may not completely dissolve the detergent.
Did you use the proper cycle time for the load? Reducing
wash time (duration) is another way to reduce lint.
Stains on load
■
Did you follow the manufacturer’s directions when adding
detergent and fabric softener?
Measure detergent and fabric
softener. Use enough detergent to remove soil and hold it in
suspension. Dilute fabric softener and add to the rinse portion
of a cycle only. Do not drip fabric softener on clothes.
■
Is there above average iron (rust) in water?
You may need to
install an iron filter.
■
Did you properly sort the load?
Sort dark clothes from whites
and lights.
■
Did you unload the washer promptly?
To avoid the transfer of
dye, unload the washer as soon as it stops.
Load is wrinkled
■
Did you unload the washer promptly?
Unload the washer as
soon as it stops.
■
Did you use the right cycle for the load being washed?
Use the cycle for Casual or Permanent Press clothes or another
cycle with low spin speeds (if available) to reduce wrinkling.
■
Did you overload the washer?
The wash load must be
balanced and not overloaded. Loads should move freely during
washing.
To reduce wrinkling of permanent press clothes and some
synthetic knits, use a large load size to provide more space.
■
Are the hot and cold water hoses reversed?
Check that the
hot and cold water hoses are connected to the right faucets.
See the Installation Instructions.
Load is tangled or twisted
■
Did you overload the washer?
The wash load must be
balanced and not overloaded. Loads should move freely during
washing.
■
Did you wrap items around the agitator?
Drop items loosely
into the washer. Do not wrap items around the agitator.
Gray whites, dingy colors
■
Did you properly sort the load?
Transfer of dye can occur
when mixing whites and colors in a load. Sort dark clothes from
whites and lights.
■
Was the wash temperature too low?
Use hot or warm
washes if safe for the load. Make sure your hot water system is
adequate to provide a hot water wash.
■
Did you use enough detergent, or do you have hard water?
Use more detergent for washing heavy soils in cold or hard
water.
■
Are the hot and cold water hoses reversed?
Check that the
hot and cold water hoses are connected to the right faucets.
See the Installation Instructions.