Filter
Top Products
Easy iron
This function allows your
washing to come out of the
machine without creases,
making it much easier to iron.
You can use it with programmes
3-4 (Cotton), 5-6-7 (Synthetics)
and 9-10 (Delicates).
Press this button in
programmes 5-6-7-9-10 and the
wash cycle will come to a stop
on symbol
. You can comple-
te it by pressing button E again.
Important:
this function should
not be used when button H
(stain removal) has been
pressed.
Extra rinsing
This helps to increase the amount
of rinse cycles in programmes for
cotton and synthetics fabrics. We
recommend that you use it to
improve the machine's rinsing
power when dealing with a full load
and a great amount of detergent.
Rapid wash
This button reduces the length
of the wash programme by
about 30%. It cannot be used
with special programmes (see
page 4) or those for wool and
silk.
Stain removal (see page 19)
Thanks to this command, the
washing machine will carry out
a more intensive wash that
optimises the effectiveness of the
liquid additives, thus allowing
more resistant stains to be
removed. When you press the
stain removal button, you cannot
activate the pre-wash.
Here I’m in command
Understanding the control panel
Making the right choice is important. And it’s easy.
Programme selector knob
Use this knob to select the wash
programme.
Turn this knob clockwise only.
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointer on the knob.
Now press on/off button I
(position I), pilot lamp L will start
flashing.
After 5", the setting will be
accepted, pilot lamp L will stop
flashing (staying lit) and the
wash cycle will begin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols
(Stop/Reset) and
wait 5" : when the cancellation
has been accepted, pilot lamp
L flashes, and you can then turn
the appliance off.
After the wash cycle has been
set and accepted by the
washing machine, turning the
knob will have no effect (except
for when it is on position
Stop/
Reset).
Temperature control knob
It is used to set the wash tempe-
rature in the recommended
programme table on pag. 4. It also
allows you to reduce the tempe-
rature recommended for the
selected programme, and even
to set a cold wash cycle (
).
Spin exclusion knob
It is used to exclude the spin cycle
(by choosing symbol
) or to re-
duce the spin speed of the selected
programme. The maximum speed
for the four types of fabric are:
Fabric Speed
Cotton 1300 rpm
Synthetics 800 rpm
Wool 600 rpm
Silk no
Note: distribution phase will be
carried out at low speed.
Detergent dispenser
It is divided into 3 compartments:
1.Detergent for pre-wash;
2.Detergent for the main cycle
wash;
3. Fabric conditioner.
The washing machine is
equipped with an extra
compartment 4 (provided as an
accessory) for the bleach, to be
inserted in compartment 1.
3
Instructions for installation and use
L
M
A
B
C
I
D
G
H
E
F
On-off
When button I is pressed, the
washing machine is switched
on, when it is not the machine
is switched off.
Turning the appliance off
does not cancel the selected
programme.
The on-off lamp
Lamp L flashes when the
appliance is switched on and
awaiting a programme to be set.
A steady light means the
appliance has accepted the
selected programme.
The door block lamp
The safety lamp indicates that the
washing machine door is locked
to prevent it from being opened
accidentally. To avoid any
damages to lock mechanism,
you must wait for the lamp to
extinguish, before attempting to
open the door which takes around
three minutes.
1
2
3
4
The detergent dispenser with the
additional bleach compartment
is here.