Filter
Top Products
9
3.
Run the foam-removing spinning.
(a) Open the outer cover of the spin tub.
(b) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute. It the water quantity
filled is too large, the water may flow out
from the wash tub side. Please twist the
water tab to limit the water filling.
(c) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
Put the laundries into the spin tub evenly and smoothly.
Spin
(a) Put the gland in properly.
Please put in the gland properly even if the laundries quantity is small.
(b) Close the inner and outer cover of the spin tub.
(c) Spin for 1-2 minutes.
2.
1.
Midway spinning
Outer cover of
The spin tub
Inner cover of
The spin tub
Push
Proper
The laundries
are slanting
Proper
No
gland
Push
Gland
WASH SPIN
4
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.
Install the lint filter
After opening the package, please take
out the lint filter from the document bag,
install it to the overflow filter of the wash
tub. See to the figure.
The drainage shall be smooth with the
drain hose.
1. The height of the drain hose shall be
less than 10cm, or the drainage will
not be smooth enough and cause
incomplete drainage.
2. Do not tramp or press the drain hose.
3. If the drain hose is too long,
cut it at mid point. To make
smooth drainage, cut the
front end of the hose
slantingly.
4. If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
be less than 30mm, and the length
shall not exceed 1.5m.
If the extra hose is too long, cut it
either at point A or B.
Usage of the drain hose
> 30mm
<1.5m
<10cm
A B
Overflow filter
Lint filter
8
Washing sequence
1. Water fill selection
(a) Set fill selection to 'Wash
side'. (Figure 1)
(b) Adjust water level rod to a
position as needed.
2. Fill water and add disolved
powder detergent until water
reaches a suitable level. (Figure)
2) Begin to wash to dispense
detergent uniformly.
3. Put in the wash load, and
supplement water as necessary.
4. Wash selector knob
Select the washing speed
according to the laundries.
(Figure 3)
5. Select the washing time
Select the washing time
according to the laundries.
(Figure 4)
6. After washing, the buzzer will
ring.
Set the "WASH SELECTOR" at
"DRAIN". (Figure 5)
Wash
Figure 2
*WASH TIMER
OFF
3
6
12
6
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
WASH SELECTOR
Figure 5
DRAIN
STRONG
STANDARD
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
WASH SELECTOR
Figure 3
DRAIN
STRONG
STANDARD
#
SOAK TIMER
Figure 4
35
25
15
5
OFF
Figure 1
SPIN
WASH
Water inlet
Water filling
control handle
SPIN
WASH
SPIN TIMER
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
OFF
7
2
3
4
5
Overflow sign
Spin timer
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
* For the model with Wash Timer.
# For model with Soak Timer.
Wash selector
(standard wash speed,
strong wash speed)
WASH SELECTOR
DRAIN
STANDARD
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Wash/Soak timer
(To set to below 2 minute,
first set to 6 minute then
turn it back. it can increase
the service life of the timer).
WASH/SOAK TIMER
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
OFF
3
6
9
12
15
I
I
STRONG
3
Safety precautions
Petrol
Thinner
Do not stretch hands into the
working machine. It is dangerous
even if the rotation is slow. Take
special care of the children.
Handicapped or children without
care shall not use the machine.
Do not put any hot or heavy items
(such as the kettle with hot water) on
the washing machine.
Do not decompose, repair or alter
the machine by yourself.
Keep the machine away from direct
sunlight and heat source like the
heater.
Do not wash laundries with volatile
materials (such as thinner, petrol
etc.).
Please put down the drain hose before washing, and connect the water inlet
pipe properly.
It is suggosted to use foamless washing powder.
0
Please don't use the washer in the environment below 0 C.If the washer is
0
bleow 0 C, the washer's water inlet system and draining system will be
frozen, then result in the damaged of the whole machine. If the washer has
0
below 0 C, please be sure to ensure the washer is placed under the room
temperature for 2-4 hours and then use.
To protect your laundry and washing machine,
please take out all coins, buttons, sand, hairpins and
other foreign materials from the clothes before
washing.
7
The musts in washing
Usage of the detergent
Fill water to decided level.
Dilute the whitener with
container. Pour it slowly into
the washing tub.
Avoid using whitener on
laundries with color or pattern
as they are prone to lose color.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
For powder whitener, please
dissolve it before using.
It is suggested not to use high
sudsing detergent.
•
•
•
•
•
•
Direct dissolved in the machine:
1. Fill small quantity of water.
2. Add the powder. Run for 30
seconds to dissolve it completely.
3. Put it in the laundries. Select
suitable water level.
The instant dissolving of the
washing powder.
0
1. Prepare warm water of 30 C and
a container.
2. Add the powder while stirring to
fully dissolve it.
The powder is more prone to pollute
the laundries than the detergent.
Therefore please use it with proper
quantity.
Dosage of different washing powder
is different. Please refer to the
instruction of the washing powder
for the detail dosage.
•
•
•
•
The capacity of washing and spinning of
the machine refer to the largest weight of
the standard laundries under dry condition
that can be washed or spinned in one time.
Laundries quantity in one washing cycle
shall be lower than the rated capacity.
The thickness, size, type of the cloth will
influence the actual washing capacity. It is
suitable to put in reasonable amount of
laundries and the laundries can be turned
round in washing for one time washing.
Do not select "Maximum" water level for
laundries less than 1.0kg, so as to avoid
splashing of water.
How to use the whitener
How to use the washing powder
•
•
•
2
Safety precautions
In case the washing machine is
installed on ground with carpet, do not
block the ventilation hole with carpet.
Do not put the machine at damp
place like the bathroom . Never wash
it with water. Do not place wet
laundries on the control panel.
Do not use water hotter than 50 C.
Do not let the machine share one receptacle
with other electric appliances. If the power plug
is damaged, or the plugging into the receptacle
is loose, do not use the plug any more.
Do not wash water-pfoof laundries
like the raincoat, bike covers etc. to
avoid abnormal vibrations in spinning.
Please insert the power cord into
special receptacle with rated
voltage. Be sure to use single-
phase three pins receptacle.
The earthing terminal of the
receptacle must be earthed
reliably. If possible, please adopt
electric leakage protector.
When the machine is being used
normally, please put the power
plug at the location easily to be
inserted and extracted by hand.
Be sure to pull the plug off when
there's power failure, or the
machine is being moved,
cleaned of when it is idle.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Ventilation hole at
the bottom of the
washing machine
50 C
6
Preparation before washing
Preparation before washing:
1. Connect the water inlet hose.
2. Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal to
the gas pipe and tap water pipe.
3. Put down the drain hose.
4. Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Check if Clear the Tie the long The quantity of When the pulsator
the laundries pocket. Take strips; fasten the laundries is running, the buttons
has any out the coins, the buttons; shall not be too of the laundries may
special sand, hairpins close zippers. large. Stretch cause noise. For the
requirement etc. and loosen the sake of discretion,
for washing. laundries before please wash the
(fabric putting them in laundries with buttons
should the tub. separately (along with
be marked laundry washing bag).
machine
wash)
a. Check if the laundries are applicable for washing in machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Soak those laundries which absorb water with difficulty, by hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or
dust. for the parts with heavy soil, please apply detergent on them in
advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it
over before putting in machine.
f. Do not put the laundries polluted by chemicals into the washing machine
directly.
Pay attention to followings before washing the laundries
1
Names of the parts
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
Spin tub
Cabinet
Major frame
Base frame
Wash selector
Wash/Soak timer
Control panel
Overflow filter
Water level adjusting lever
Pulsator
Wash tub
Drain hose
Wash tub cover
Water-filling entrance
Valve cover
Protecting cover
All illustrations in this manual are given for reference only. Your
products and accessories may show differences from these
illustrations due to our continuous improvement.
Notes:
Meaning and description of the symbols
Contents marked with that symbol are
related to the safety of the product and the
personal safety of the users. Please
operate in strict conformity to the contents,
otherwise it may cause damage of the
machine or injure the personal safety of
the user.
Contents marked with that symbol are
actions forbidden to perform. Performing of
those actions may result in damage of the
machine or injure the personal safety of the
user.
Please check if the power receptacle has good earthing condition
before using to guarantee your safety.
Warning sign
Forbidding sign
•
5
Figure 1
Drain hose
fixing hook
Figure 2
Drain hose
fixing hook
Pull outwards
slightly
Side sectional view
Fixing hook
installation hole
Drain hose
Take off
the drain hose
Figure 5
Figure 6
How to change the direction of the drain hoses
Install the water inlet hose; Select the water level
Figure 1 indicates the ex factory
installation position of the drain hose.
Take off the drain hose from the hanging
hole of the cabinet. Pull the drain hose
fixing hook outwards gently to take out
the drain hose from the two fixing hooks.
(As per figure 2)
0
Rotate the drain hose fixing hook for 90
to take it out from the installation hole (As
per Figure3).
Install the two drain hose fixing hooks
taken out into the installation hole at the
other side of the base frame (to aim at the
installation hole accurately you can lean
the washing machine forward slightly).
0
Then rotate for 90 (As per Figure 4).
Pull the fixing hook outwards slightly.
Inlay the drain hose into the fixing hooks
reliably along the groove at spin tub side,
and make it extendtowards spin tub side.
Then hang the drain hose into the
hanging hole at the spin tub side. (As per
Figure 5).
Take out the drain hose from the fixing
hook. Extend it from the near side (When)
the drain hose is extended from the rear
side, it can be hung on the point for drain
hose at the two sides of the cabinet.) (See
to Figure6).
•
•
•
•
•
•
•
•
•
Extend the drain hose from the side of spin tub
Extend the drain hose from the rear side
Insert the water inlet hose into the water-
filling entrance on the control panel directly-
(pull it out to dismantle it)
Select water level according to the quantity
of the laundries.
Set the water level adjusting lever to
needed line.
Figure 4
Insert the fixing hook into the
installation hole upwards
Rotate the fixing
hook for 90ｰ
to fix it
Figure 3
Take off the fixing
hook downwards
Rotate the fixing
hook for 90ｰ
Water inlet hose
Water inlet
Max
Med
Min
Maximum
Medium
Minimum
Water level
indicator
Contents
• Names of the parts 1
• Safety precautions 2
• Installation and adjustment 4
• Preparation before washing 6
• The musts in washing 7
• Usage of the detergent 7
• Washing sequence 8
• Disposal after washing 12
• Trouble-Shooting * Answer to question 14
• Packing list *Specification 16
Gripper