Filter
Top Products
137102600 (0806)
Towels Normal Perm Press Delicate Quick Bulky Timed Dry
Estimated
drying time ***
60 minutes 50 minutes 40 minutes 20 minutes 30 minutes 45 minutes
15 to 90
minutes
Temperatures
High
*
Medium-High
*
*
Medium
*
*
*
Low
*
No Heat
** ** ** **
Dryness Level
More Dry
Normal Dry
* * *
Less Dry
*
Damp Dry
Options
Shrink Guard
*
Press Saver
*
*
Cycle Signal
*
*
*
*
*
*
*
* Factory Available ** Not
*** Estimated cycle duration is based on normal
dryness level and factory settings.
setting settings recommended
DRYER SETTINGS CHART
AVAILABLE CYCLE SETTINGS - These temperatures, dryness levels and options are available with the following cycles:
Cycle Selection (Con’t)
Drying Temperature
For best results, follow the fabric care label instructions on items
to be dried. To change the drying temperature, press TEMP to
scroll to the desired heat. To protect your wardrobe, not all
temperatures are available with every cycle.
High heat is recommended for sturdy fabrics.
Medium High heat is recommended for most cotton fabrics.
Medium heat is recommended for wrinkle free, permanent press
and lightweight fabrics.
Low heat is recommended for delicate fabrics.
No Heat should only be used with a Timed Dry setting to dry
items containing feathers, down, foam rubber, plastics or rub-
ber-like materials; to freshen clothing, pillows or blankets; or to
dust draperies.
Note: Using No Heat in any Auto Dry cycle will result in
long drying times and /or wet loads at the end of the cycle.
Cycle Settings
Appropriate drying temperature, dryness level and options will
automatically be indicated for each cycle. The TEMP, DRYNESS
and OPTIONS settings can be changed before the cycle is
started. Those adjustments will automatically be remembered
each time that cycle is selected. If a temperature, dryness level
or option is not recommended for a cycle, the indicator will not
light.
If changes are attempted after the cycle starts, the status lights
will blink, the signal will beep and “Err” will be displayed. To
change a setting after the cycle starts, press Pause/Cancel once,
adjust the setting and press START to resume the cycle. See
the “Dryer Settings Chart” for more details.
Dryness Level
To change the dryness level, press DRYNESS until the desired
selection is made. Select Normal for most loads.
Occasionally a load may seem too damp or over-dried at the end
of the cycle.
To increase drying time for similar loads in the future, select
More Dry. For loads requiring less drying time, select Less Dry.
Select Damp Dry for items you wish to partially dry before hang-
ing or ironing.
Note: To prevent over-drying, not every dryness level is
available with every cycle.
Options
To select an option, press OPTIONS until the indicator for the
desired option flashes, then press Select. If an option is not
available for a cycle, the indicator will not light. Follow the same
steps to delete an option.
The Cycle Signal will sound at the end of the cycle and periodi-
cally during Press Saver.
Select Shrink Guard to lower the initial drying temperature to
protect fabrics from overdrying.
Select Press Saver if the dried load might not be removed
promptly at the end of the cycle. The dry load will continue to
tumbling without heat for 30 minutes to help reduce wrinkling.
When the Cycle Signal is selected, a beep will be heard
periodically. The load may be removed any time during Press
Saver.
Dryer Features
(Control Lock)
To avoid having someone accidentally start or stop the washer,
press OPTIONS and Select at the same time and hold for about
10 seconds until the (Control Lock) lights up. “LOC” will be
displayed alternately with the estimated cycle time. Turning
the Cycle Selector knob or pressing any button will produce
flashing indicator lights and/or beeping. To unlock the controls,
press and hold OPTIONS and Select for about 10 seconds.
Status Lights
The following indicators may be lighted during the cycle:
• Drying
• Cool Down
• Press Saver
• Clean Lint Filter
• (Control Lock)
* Factory setting
Available
settings
** Timed Dry
Cycle Only
*** Estimated
cycle duration is
based on normal
dryness level and
factory settings.
These temperatures, dryness levels and options are available with the following cycles: