Filter
Top Products
You can use the garment head diffuser
with the hose or alone on the unit itself. To
attach, align the pins on the
garment head diffuser with
the slots on the appliance.
Both the angle adapter and the small detail
brushes can only be used directly on the
concentrator nozzle. When using with the
concentrator nozzle, push the attachment
onto the end of the concentrator nozzle.
Concentrator Nozzle
To attach the concentrator nozzle to the
nozzle of the unit, align the pins on the
concentrator nozzle with the slots on the
appliance. (See illustration.) Push the
attachment onto the nozzle until it stops
against the appliance body. Turn in a
clockwise direction 90°. The attachment
is now locked into position.
ATTACHMENTS
How To Assemble & Use
Step 1: Before filling the steam cleaner,
make sure that the unit is NOT
plugged in.
Step 2: Turn Safety Cap counter
clockwise until removed.
Step 3: Add 20 fl. oz (600 cc) of water
using the filling flask provided.
Do not overfill. Replace
Safety Cap by turning
clockwise - press down firmly to
tighten. Heating time is
approximately 6 minutes. Filling
the boiler with hot water will
shorten heat up time.
Step 4: Plug the unit into a standard
120 volt wall receptacle. The
power “On” light (Red) will light
up.
Step 5: Allow approximately 3-5
minutes for water vapor to
reach its working
temperature and pressure.
When unit is ready for use the
red light will change to Green.
Step 6: At the start, some water will
come out from the nozzle. This
is normal.
Refilling With Water
Step 1: Disconnect electrical power
cord from wall outlet.
Step 2: Press trigger button until all
pressure has been released.
Carefully unscrew safety
cap.
Step 3: Allow the unit to cool for
approximately 5 minutes
before refilling with water.
Step 4: Slowly pour water using the
filling flask into the boiler.DO
NOT Fill Under a faucet,
use the filling flask
provided. DO NOT
OVERFILL. Always leave
approximately 2 1/2 inches
between the top of the unit
and the water level.
Step 5: Release the locking trigger.
Step 6: Screw safety cap back on t
he appliance and plug
appliance back into wall
outlet. Steam will start to be
produced as before.
OPERATING INSTRUCTIONS
IMPORTANT: Always insure that the
unit is “UNPLUGGED” from the wall
receptacle prior to initial filling or re-filling
the water tank. Never attempt to fill this
unit under a water tap, always use the
filling flask provided. Failure to follow
these steps will cause the water tank to
overfill and may pose an electrical safety
hazard.
Using the Locking Trigger Button
The steam cleaner has a locking trigger
button. As you push down on the trigger
you will get more steam. The trigger will
lock when you have pushed it all the
way. To unlock the trigger, just press
down on the trigger release and the
trigger will pop up, stopping the flow of
steam.
OPERATING INSTRUCTIONS cont.
Window Squeegee
CAUTION: When cleaning windows,
always avoid any sudden changes in
temperature to prevent glass breakage
or cracks.
To remove the
window
squeegee from
the garment
diffuser head,
just push your
thumb against
the locking tab
on the window
squeegee.
To attach the window squeegee to the
garment diffuser head, place the two
hinges at the back of the window squeegee
(see illustration) into the two open tabs that
are at the back of the garment diffuser
head. Swing the window squeegee up
against the bottom of the garment diffuser
head until the locking tab engages.
Small Detail Brush / Angle Adapter
Attaching the Shoulder Strap
Using the detachable
shoulder strap allows
for greater freedom of
movement when both
hands are needed for
various cleaning tasks.
To attach the shoulder
strap to the steam
cleaner, simply
snap the shoulder
strap hooks onto the
connecting rings on the
unit body. When using
the steam cleaner
with the shoulder strap,
avoid rocking or tilting
the unit excessively as
this may cause water to
enter the hose and be
discharged along with the steam.
NOTE
: Disconnect steam cleaner from
wall outlet before refilling. It is time to refill
your steam cleaner when there is no more
steam coming out of the nozzle. Because
the water tank is pressurized, use caution
when opening to refill. Depress the trigger
button while you unscrew the safety cap
counterclockwise. Always let unit cool for
5 minutes before refilling the unit with
water.
Garment Diffuser Head
WARNING: This appliance is under
pressure. After every use, press trigger
button until all pressure has been
released before removing safety cap.
Either concentrator nozzle or hose must
be connected in order for the trigger to
operate. Allow unit to cool for three (3)
minutes before refilling.
CAUTION
: When refilling the appliance
while it is still hot, the first drops of
water might bubble up.
5 6