Filter
Top Products
IMPORTANT SAFETY INSTRUCTIONS
1. Read all instructions carefully.
2. Use iron only for its intended use.
3. To protect against risk of electrical shock,
do not immerse the iron in water or other
liquids.
4. Never yank cord to disconnect from outlet.
Grasp plug and pull to disconnect.
5. Do not allow cord to touch hot surfaces.
Let iron cool completely before putting
away.
6. Always disconnect iron from electrical
outlet when filling with water, emptying, or
when not in use.
7. Do not operate iron with a damaged cord,
or after the iron has been dropped or
damaged in any manner. To avoid the risk
of electric shock, do not disassemble the
iron. Return the iron to EURO-PRO
Operating LLC for examination and
repair. Incorrect reassembly can cause
the risk of electric shock when the iron is
used.
8. Close supervision is necessary for any
appliance being used by or near children.
Do not leave iron unattended while
connected or on an ironing board.
9. Burns can occur from touching hot metal
parts, hot water or steam. Use caution
when you turn a steam iron upside down;
there may be hot water in the reservoir.
10. Never use or rest iron on an unstable
surface.
11. While the iron is hot, never set iron on an
unprotected surface - even if it is on its
heel rest.
12. CAUTION! TO PREVENT ELECTRIC
SHOCK OR OTHER INJURY, before
filling the iron with water, make sure
that the plug is removed from the
outlet.
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not
operate another high-wattage
appliance on the same circuit.
2. If an extension cord is absolutely
necessary, use a 15-ampere cord.
Cords rated for less amperage may
overheat. Use care to arrange the cord
so that it cannot be pulled or tripped
over.
SAVE THESE INSTRUCTIONS
1
POLARIZED PLUG: This appliance has a polarized plug (one blade is wider than
the other). As a safety feature, this plug will fit into a polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety feature.
For Household Use Only
Rev. 08/07
13. WARNING: Never fill the iron with
fabric conditioner, starches or any
other solution, as these will damage
the steam mechanism. Do not use
contaminated water.
14. CAUTION! TO AVOID FIRE, never
leave iron unattended while it is
plugged in.
15. CAUTION! TO PREVENT ELECTRIC
SHOCK, never use the iron in a
location where it can fall or be pulled
into water or another liquid. If the iron
falls into water or other liquid, unplug
it immediately. DO NOT reach into the
water or liquid.
16. WARNING: Never use scouring pads,
abrasive or chemical cleaners, or
solvents to clean the exterior or
soleplate of your iron. Doing so will
scratch and/or damage the surface.
17. CAUTION! DO NOT aim iron at face,
towards yourself, or anyone else while
using or adjusting steam. Burns or
serious injury may occur.
18. Always store your iron standing upright,
not on the soleplate. If stored face down,
even the smallest amount of moisture will
cause the soleplate to corrode and stain.
19. This appliance is for household use
only.
TROUBLESHOOTING
PROBLEM POSSIBLE REASONS & SOLUTIONS
Iron does not heat
Some odor or small
particles come out of
steam vents of new
iron
Iron does not steam
Water droplets coming
from steam vents
• Iron should be plugged into a 120V AC electrical
outlet only.
Make sure that the plug is securely in the socket.
• Temperature setting too low.
Turn to higher setting.
• This is normal.
Follow instructions for first use and allow iron to steam
through 2-3 fillings & press the steam burst button
occasionally to eliminate small white particles.
• Water tank may be empty or water level is very low.
Add water.
• Make sure that the fabric/temperature setting and
the variable steam control are correctly set. For
maximum steam, (setting ‘Max’ on steam control),
temperature setting should be set on ‘•••’.
• Variable steam control dial is set on “0”.
Always allow the iron to reach the selected
temperature with the variable steam control setting
at ‘0’. Make sure the temperature setting is set in
the correct steam area, e.g. ‘•’, and the steam control is
not
on ‘0’. For more steam, turn temperature dial to
higher setting, e.g. ‘•••’, and the steam control to ‘Max’.
• If temperature setting and steam control setting are
correct and there is no steam, gently
tap the
soleplate on the ironing board a few times. Move
the variable steam control from ‘0’ to ‘Max’ a few
times.
• Iron may not be hot enough. Set thermostat to the
‘Max’ position. Always allow iron sufficient time to
heat up before activating the variable steam control.
• Overuse of steam burst. Allow more time between
each burst.
• Iron may have been overfilled. Turn iron off,empty
water and follow instructions for filling.
• Steam performance may be low if iron requires
seasoning. To season, use regular tap water for 1or 2
tanks until steam performance improves.
10
When using your iron, basic safety precautions should always be followed, including the following: