Filter
Top Products
Included in the accessories supplied with this machine are 2
inlet hoses and 4 rubber washers. The straight end of these
hoses should be connected to the supply fig. 1.
The 90° angled end of these hoses should be connected to
the inlet valves on the back of the machine, using one of the
washers to make a water tight seal on each connection. The
couplings should be tightened by hand, a tool should only be
used if a leak occurs. Do not use excessive force (see M, fig.
1).
The inlet valves are color coded:
Red Red
Red Red
Red = Hot
WhiteWhite
WhiteWhite
White = Cold
It is possible to run the machine on a single faucet with cold
water only, but water must be supplied to each inlet valve. The
“Y“ connector allows a single water source to be split into the
two inlets at the rear of the appliance (see fig. 2).The “Y”
connector is part of the faucet available kit - available as an
accessory from Equator Parts 1-888-483-9627.
PLUMBING (Water Inlet)
You should carefully position the drain hose to avoid kinks
and ensure proper drainage of the water.
The outlet end of the drain hose must be at least 25” (62 cm)
above the base of the machine. At this point it is possible for
the water to be discharged into a sink or drain pipe, but an air
break must be available at this 24” height to prevent the machine
from syphoning (see fig. aside).
No more than 6” of the drain hose should be inserted in the
drain pipe.
IMPORIMPOR
IMPORIMPOR
IMPOR
TT
TT
T
ANTANT
ANTANT
ANT
make sure that the drain hose is not kinked and the water flow
has not been restricted.
Standpipe drain system:Standpipe drain system:
Standpipe drain system:Standpipe drain system:
Standpipe drain system:
In RV installation needs a 1-1/2 inch (3.7 cm) diam.
standpipe with minimum carry away capacity of 7
gallons (31 liters) per minute or 2” (5 cm) in home
installation.
Floor Standpipe drain:Floor Standpipe drain:
Floor Standpipe drain:Floor Standpipe drain:
Floor Standpipe drain:
Top of standpipe must be at least 25 inches (62
cm) high and no higher than 34 inches (86 cm)
from the bottom of washer
(A)(A)
(A)(A)
(A).
WW
WW
W
all standpipe drain:all standpipe drain:
all standpipe drain:all standpipe drain:
all standpipe drain:
25 inches (62 cm) min.; 34 inches (86 cm.) max
from end of drain hose to bottom of washer
(B) (B)
(B) (B)
(B).
PLUMBING (Water Out)
Fig. 1 - Water pipe inlet at the top right
25
2
77
77
7 Instructions for installation and use
25”
34”
Connection to the water mains
Water pressure must range within the values indicated on the data
plate on the rear of your washer-dryer. If the water pipes are new or left
unused, then before connecting the machine run the water until clear
to remove debris. Connect the inlet hose to a cold water tap having a
¾ “ BSP thread. Ensure that the rubber sealing washer-dryers are
fitted at each end of the inlet hose, with the fitter washer-dryer at the tap
end.
Connect the inlet hose to the threaded connector on the machine
rear.
Fig.2 - The joint Y
for doule water supply
EXHAUSTING
The appliance should not be
exhausted into a chimney,
wall, ceiling or any concealed
space of a building. Only rigid
or flexible metal duct should
be used for exhausting.
AIR OUTLET FILTER
ATTACHMENT
A special vent kit is available
from your dealer
Note:Note:
Note:Note:
Note: Replace inlet hoses after
5 years of use to reduce the risk
of hose failure. Record hose
installation or replacement
dates on the hoses for future
reference.
Periodically inspect and replace
hoses if bulges, kinks, cuts,
wear or leaks are found.