Blomberg WNF 7321 AE20 Washer User Manual


  Open as PDF
of 68
 
13
EN
display. The Child Lock does not allow any
change in the programmes and the selected
temperature, speed and auxiliary functions.
C
Even if another programme is selected with the
ProgrammeSelectionknobwhiletheChildLock
is active, previously selected programme will
continue running.
To activate the Child Lock:
Press and hold 1
st
and 2
nd
AuxiliaryFunctionbuttons
for 3 seconds. The lights on the 1
st
and 2
nd
Auxiliary
Functionbuttonswillflash,and"C03","C02","C01"
will appear on the display respectively while you keep
thebuttonspressedfor3seconds.Then,"Con"
will appear on the display indicating that the Child
Lockisactivated.Ifyoupressanybuttonorturnthe
ProgrammeSelectionknobwhentheChildLockis
active, same phrase will appear on the display. The
lightsonthe1stand2ndauxiliaryfunctionbuttons
thatareusedtodeactivatetheChildLockwillblink
3 times.
To deactivate the Child Lock:
Press and hold 1
st
and 2
nd
auxiliaryfunctionbuttons
for 3 seconds while any programme is running. The
lights on the 1
st
and 2
nd
AuxiliaryFunctionbuttons
will flash, and "C03", "C02", "C01" will appear on
thedisplayrespectivelywhileyoukeepthebuttons
pressedfor3seconds.Then,"COFF"willappear
on the display indicating that the Child Lock is
deactivated.
C
Inadditiontothemethodabove,todeactivate
the Child Lock, switch the Programme Selection
knobtoOn/Offpositionwhennoprogrammeis
running, and select another programme.
C
Child Lock is not deactivated after power failures
or when the machine is unplugged.
C
IfyouswitchoffthemachinebypressingtheOn
/OffbuttonwhentheChildLockisactiveand
the machine is running, then the child lock will
bedeactivated.
Progress of programme
Progressofarunningprogrammecanbefollowed
fromtheProgrammeFollow-upindicator.Atthe
beginningofeveryprogrammestep,therelevant
indicator light will turn on and light of the completed
step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make must
beinastepaftertherunningprogrammestep.Ifthe
changeisnotcompatible,relevantlightswillflashfor
3 times.
C
Ifthemachinedoesnotpasstothespinning
step,RinseHoldfunctionmightbeactiveorthe
automaticunbalancedloaddetectionsystem
mightbeactivatedduetotheunbalanced
distributionofthelaundryinthemachine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
whenthewaterlevelisunsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine
checksthelevelofthewaterinside.Ifthelevelis
suitable,LoadingDoorlightilluminatessteadilywithin
1-2minutesandtheloadingdoorcanbeopened.
Ifthelevelisunsuitable,LoadingDoorlightturnsoff
andtheloadingdoorcannotbeopened.Ifyouare
obligedtoopentheLoadingDoorwhiletheLoading
Doorlightisoff,youhavetocancelthecurrent
programme; see "Canceling the programme".
Changing the selections after
programme has started
Switching the machine to pause mode
PresstheStart/Pausebuttontoswitchthemachine
to pause mode while a programme is running.
The light of the step which the machine is in starts
flashingintheProgrammeFollow-upindicatorto
showthatthemachinehasbeenswitchedtothe
pause mode.
Also,whentheloadingdoorisreadytobeopened,
LoadingDoorlightwillalsoilluminatecontinuouslyin
addition to the programme step light.
Changing the speed and temperature settings
for auxiliary functions
Dependingonthesteptheprogrammehasreached,
you may cancel or activate the auxiliary functions;
see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C
Ifnochangeisallowed,therelevantlightwill
flash for 3 times.
Adding or taking out laundry
PresstheStart/Pausebuttontoswitchthemachine
topausemode.Theprogrammefollow-uplightof
the relevant step during which the machine was
switched into the pause mode will flash. Wait until
theLoadingDoorcanbeopened.OpentheLoading
Doorandaddortakeoutthelaundry.Closethe
LoadingDoor.Makechangesinauxiliaryfunctions,
temperature and speed settings if necessary. Press
Start/Pausebuttontostartthemachine.
C
The loading door will not open if the water
temperature in the machine is high or the water
levelisabovethedooropening.
Canceling the programme
To cancel the programme, turn the Programme
Selectionknobtoselectanotherprogramme.
Previousprogrammewillbecanceled.End/
Cancel light will flash continuously to notify that the
programmehasbeencanceled.
Pumpfunctionisactivatedfor1-2minutesregardless
of the programme step, and whether there is water
in the machine or not. After this period, your machine
willbereadytostartwiththefirststepofthenew
programme.
C
Dependingonthestepwheretheprogramme
was canceled in, you may have to put detergent
and softener again for the programme you have
selected anew.
C
Ifyouwanttoopentheloadingdoorafteryou
havecancelledtheprogrammebutitisnot
possibletoopentheloadingdoorsincethe
waterlevelinthemachineisabovetheloading
door opening, then turn the Programme
 previous next