Blomberg WNF 6200 WE 20 Washer User Manual


  Open as PDF
of 68
 
13
EN
process, the machine will switch to Pause mode
and the illumination level of the temperature,
speed and loading door indicator lights will
decrease.Otherindicatorlightsandindicators
willturnoff.OncetheProgrammeSelection
knobisrotatedoranybuttonispressed,
indicator lights and indicators will turn on again.
Child Lock
Usechildlockfunctiontopreventchildrenfrom
tampering with the machine. Thus you can avoid any
changes in a running programme.
C
IftheProgrammeSelectionknobisrotated
when the child lock is active, the lights on the
1
st
and 2
nd
auxiliaryfunctionbuttonswillblink
3 times. The child lock does not allow any
change in the programmes and the selected
temperature, speed and auxiliary functions.
C
Even if another programme is selected with the
ProgrammeSelectionknobwhiletheChildLock
is active, previously selected programme will
continue running.
C
When the Child Lock is active and the machine
is running, you can switch the machine to Pause
modewithoutdeactivatingtheChildLockby
turningtheProgrammeSelectionknobtoOn
/Offposition.WhenyouturntheProgramme
Selectionknobafterwards,theprogrammewill
resume.
To activate the Child Lock:
Press and hold 1
st
and 2
nd
AuxiliaryFunctionbuttons
for 3 seconds. The lights on the 1
st
and 2
nd
Auxiliary
Functionbuttonswillflashwhileyoukeepthebuttons
pressed for 3 seconds.
To deactivate the Child Lock:
Press and hold 1
st
and 2
nd
auxiliaryfunctionbuttons
for 3 seconds while any programme is running. The
lights on the 1
st
and 2
nd
AuxiliaryFunctionbuttons
willflashwhileyoukeepthebuttonspressedfor3
seconds.
C
Inadditiontothemethodabove,todeactivate
the Child Lock, switch the Programme Selection
knobtoOn/Offpositionwhennoprogrammeis
running, and select another programme.
C
When the power is restored after a power failure
or after your machine is unplugged and plugged
inagain,theChildLockwillnotbedeactivated
when the machine resumes operating.
Progress of programme
Progressofarunningprogrammecanbefollowed
fromtheProgrammeFollow-upindicator.Atthe
beginningofeveryprogrammestep,therelevant
indicator light will turn on and light of the completed
step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make must
beinastepaftertherunningprogrammestep.Ifthe
changeisnotcompatible,relevantlightswillflashfor
3 times.
C
Ifthemachinedoesnotpasstothespinning
step,RinseHoldfunctionmightbeactiveorthe
automaticunbalancedloaddetectionsystem
mightbeactivatedduetotheunbalanced
distributionofthelaundryinthemachine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
whenthewaterlevelisunsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine
checksthelevelofthewaterinside.Ifthelevelis
suitable,LoadingDoorlightilluminatessteadilywithin
1-2minutesandtheloadingdoorcanbeopened.
Ifthelevelisunsuitable,LoadingDoorlightturnsoff
andtheloadingdoorcannotbeopened.Ifyouare
obligedtoopentheLoadingDoorwhiletheLoading
Doorlightisoff,youhavetocancelthecurrent
programme; see "Canceling the programme".
Changing the selections after
programme has started
Switching the machine to pause mode
PresstheStart/Pausebuttontoswitchthemachine
to pause mode while a programme is running.
The light of the step which the machine is in starts
flashingintheProgrammeFollow-upindicatorto
showthatthemachinehasbeenswitchedtothe
pause mode.
Also,whentheloadingdoorisreadytobeopened,
LoadingDoorlightwillalsoilluminatecontinuouslyin
addition to the programme step light.
Changing the speed and temperature settings
for auxiliary functions
Dependingonthesteptheprogrammehasreached,
you may cancel or activate the auxiliary functions;
see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C
Ifnochangeisallowed,therelevantlightwill
flash for 3 times.
Adding or taking out laundry
PresstheStart/Pausebuttontoswitchthemachine
topausemode.Theprogrammefollow-uplightof
the relevant step during which the machine was
switched into the pause mode will flash.
WaituntiltheLoadingDoorcanbeopened.Open
theLoadingDoorandaddortakeoutthelaundry.
ClosetheLoadingDoor.Makechangesinauxiliary
functions, temperature and speed settings if
necessary.PressStart/Pausebuttontostartthe
machine.
Canceling the programme
To cancel the programme, turn the Programme
Selectionknobtoselectanotherprogramme.
Previousprogrammewillbecanceled.End/
Cancel light will flash continuously to notify that the
programmehasbeencanceled.
Your machine will end the programme when you turn
theProgrammeSelectionknob;however,itdoesnot
drain the water inside. When you select and start a
new programme, the newly selected programme will
start depending on the step the previous programme
was canceled in. For example, it may take in
additional water or continue to wash with the water
inside.
 previous next