Beko WMB 81041 L Washer/Dryer User Manual


  Open as PDF
of 52
 
3
EN
has sufficient load carrying capacity!
• Donotplacetheproductonthepowercable.
• Donotinstalltheproductatplaceswhere
temperaturemayfallbelow0ºC.
• Placetheproductatleast1cmawayfromthe
edges of other furniture.
Removing packaging reinforcement
Tiltthemachinebackwardstoremovethe
packaging reinforcement. Remove the packaging
reinforcementbypullingtheribbon.
Removing the transportation locks
A
 Donotremovethetransportationlocksbefore
taking out the packaging reinforcement.
A
 Removethetransportationsafetyboltsbefore
operating the washing machine, otherwise, the
productwillbedamaged.
1.Loosenalltheboltswithaspanneruntilthey
rotate freely (C).
2.Removetransportationsafetyboltsbyturning
them gently.
3.AttachtheplasticcoverssuppliedintheUser
Manualbagintotheholesontherearpanel.(P)
C
Keepthetransportationsafetyboltsinasafe
place to reuse when the washing machine
needstobemovedagaininthefuture.
C
Never move the product without the
transportationsafetyboltsproperlyfixedin
place!
Connecting water supply
C
Thewatersupplypressurerequiredtorun
theproductisbetween1to10bars(0.1–10
MPa).Itisnecessarytohave10–80litersof
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
C
Ifyouaregoingtousethedoublewater-inlet
productasasingle(cold)water-inletunit,you
must install the supplied stopper to the hot
watervalvebeforeoperatingtheproduct.
(Appliesfortheproductssuppliedwithablind
stopper group.)
C
Ifyouwanttousebothwaterinletsofthe
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
suppliedwithablindstoppergroup.)
A
 Modelswithasinglewaterinletshouldnotbe
connectedtothehotwatertap.Insuchacase
the laundry will get damaged or the product will
switch to protection mode and will not operate.
A
 Donotuseoldorusedwaterinlethoseson
thenewproduct.Itmaycausestainsonyour
laundry.
1.Connectthespecialhosessuppliedwiththe
product to the water inlets on the product. Red
hose(left)(max.90ºC)isforhotwaterinlet,
bluehose(right)(max.25ºC)isforcoldwater
inlet.
A
Ensure that the cold and hot water connections
are made correctly when installing the product.
Otherwise,yourlaundrywillcomeouthotatthe
end of the washing process and wear out.
2.Tightenallhosenutsbyhand.Neverusea
wrench when tightening the nuts.
3.Openthetapscompletelyaftermakingthehose
connection to check for water leaks at the
connectionpoints.Ifanyleaksoccur,turnoff
the tap and remove the nut. Retighten the nut
carefully after checking the seal. To prevent
waterleakagesanddamagescausedbythem,
keep the taps closed when the machine is not
in use.
Connecting to the drain
• Theendofthedrainhosemustbedirectly
connected to the wastewater drain or to the
washbasin.
A
 Yourhousewillbefloodedifthehosecomes
out of its housing during water discharge.
Moreover, there is risk of scalding due to
high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come
out.
• Thehoseshouldbeattachedtoaheightofat
least40cm,and100cmatmost.
• Incasethehoseiselevatedafterlayingitonthe
floor level or close to the ground (less than
40cmabovetheground),waterdischarge
becomesmoredifficultandthelaundrymay
come out excessively wet. Therefore, follow the
heightsdescribedinthefigure.
 previous next