Filter
Top Products
13 - EN
Auxiliary function
Buzzer Cancel Models Equiped
Your machine will send out an buzzer warning
when the program comes to an end. If you
do not want to hear this buzzing, you need to
press the “Cancel Audio Warning” button. The
relevant LED will light up when this button is
pressed and an audio warning will not be given
when the program comes to an end.
Warning indicators
C Warning indicators may differ according to
the model of your machine.
Filter cleaning
A warning LED will light up to remind filter
cleaning after the program finishes.
C If the filter cleaning warning LED lights up
continuously, please refer to, “Solution
suggestions for problems”.
Water tank
Warning light starts flashing when the tank is
filled with water. The dryer stops operating if
the warning light turns on when a programme
is running. Drain the water in the water tank
to restart the dryer. Press “Start/Pause/
Cancel” button to start the programme after
you have emptied the water tank. The warning
light turns off and the programme resumes
operating.
Starting the programme
1. Press “Start/Pause/Cancel” button to start
the programme.
2. Light of the “Start/Pause/Cancel” button
will turn on to indicate that the programme
has started.
Progress of program
Progress of a running program is shown
through the program follow-up indicator.
At the beginning of every program step, the
relevant indicator LED will light up and light of
the completed step will turn off.
“Drying”:
- Drying level will be illuminated during the whole
drying process until the drying degree reaches “
Ready to Iron “.
“ Ready to Iron “:
- Starts to illuminate when the drying degree
reaches “ Ready to Iron “ step and remains
illuminated until the next step.
“ Ready to Wear “:
- Starts to illuminate when the drying degree
reaches “ Ready to Iron “ step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the program comes to an
end and anti-creasing function is activated.
C If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the program after the
program has started
You can use this feature to dry your clothes
under higher or lower temperatures after your
dryer has started.
For example;
1. Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
2. Select the “Extra Dry” programme by
rotating the programme selection button.
3. Press “Start/Pause/Cancel” button to start
the programme.
C Press "Start/Pause/Cancel" button for
3 seconds to cancel the programme or
turn the programme selection knob in any
direction to end the programme while the
machine is running. Water tank and filter
cleaning warning lights turn on to warn the
user when the programme is cancelled by
pressing the "Start/Pause/Cancel" button
for 3 seconds. However, the warning
lights do not turn on when the programme
is cancelled by turning the programme
selection knob. Only the drying light turns
on and the machine remains in hold until
a new programme is selected and the
"Start/Pause/Cancel" button is pressed.
Child-proof lock of the machine should not
be active in order to perform these two
operations. If the child-proof lock is active,
deactivate it before performing these
operations.
Adding/removing laundry in standby mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button to
switch the dryer to “Pause” mode. Drying
process will stop.
2. Open the door at “Pause” position and
close it again after adding or taking out
laundry.
3. Press “Start/Pause/Cancel” button to start
the programme.
C Any laundry added after the drying process
has started may cause the dried clothes in
the machine intermingle with wet clothes
and the result will be wet laundry after the
drying process is over.
C Laundry may be added or taken out
as much as desired during a drying