Filter
Top Products
5
6
FanFresh
®
Option (on some models)
The FanFresh
®
option will periodically tumble the load after
the end of the cycle for up to 12 hours while the integrated
fan circulates air through the washer to reduce humidity.
To turn on the FanFresh
®
option, touch FanFresh. If,
however, the FanFresh
®
option is turned on, it will stay
on for all future cycles until turned back off – the washer
remembers the last on/off status set. To turn off the
FanFresh
®
option, touch FanFresh.
You may also activate the FanFresh
®
option without running
a cycle by touching and holding POWER for one second,
then touching and holding FanFresh
for 3 seconds, then
touching and holding START for 3 seconds.
To turn off the FanFresh
®
option when it is running, touch
POWER.
NOTE:
The door will lock while the FanFresh
®
option is
active.
To cancel the option and unlock the door, touch
POWER.
TumbleFresh
™
Option (on some models)
The TumbleFresh
™
option will periodically tumble the
load after the end of the cycle for up to 6 hours to reduce
humidity. To turn on the TumbleFresh
™
option, touch
TumbleFresh. If, however, the TumbleFresh
™
option is
turned on, it will stay on for all future cycles until turned
back off – the washer remembers the last on/off status set.
To turn off the TumbleFresh
™
option, touch TumbleFresh.
You may also activate the TumbleFresh
™
option without
running a cycle by touching and holding POWER for one
second, then touching and holding TumbleFresh
for 3
seconds, then touching and holding START for 3 seconds.
To turn off the TumbleFresh
™
option when it is running,
touch POWER.
NOTE:
The door will lock while the TumbleFresh
™
option is
active.
To cancel the option and unlock the door, touch
POWER.
Extra Rinse
Activate this option to add an extra rinse to most cycles.
Cycle Signal
Use this option to turn on or off the signal that sounds
at end of cycle.
To turn off the tones that sound when a setting is
touched: Touch and hold CYCLE SIGNAL for about
3 seconds. Repeat to turn them on.
Control Lock
Touch and hold for 3 seconds to lock the controls to avoid
unwanted changes or operation. Touch and hold 3 seconds
again to unlock.
For each second CONTROL LOCK is
held down, the display will count down one second: you
will see “3,” then “2,” then “1.”
You can still touch START
to pause the cycle, or touch POWER to turn off the washer.
E
C
D
C
F
LED DISPLAY AND SETTINGS
When you select a cycle, its default settings will light up and
the Estimated Time Remaining will be displayed. Factors such
as load size, wash temperature, and water pressure may affect
the time shown in the display during the cycle. Tightly packing
garments, unbalanced loads, or excessive suds may cause the
washer to adjust the cycle time, as well.
Touch the desired setting along the bottom of the display to
adjust. See “Cycle Guide” for available settings on each cycle.
Not all settings are available with all cycles.
Cycle Status Lights
For details, see the “Cycle Status Lights” section on the
next page.
Wash Temp
The recommended wash temperature is preset for each
cycle. You may also select a wash temperature based on
the type of fabric and soils being washed. For best results,
follow the garment label instructions. All wash temperatures
feature a cold rinse.
Spin
This washer automatically selects the spin speed based on
the cycle selected. Some preset speeds can be changed.
•
Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
•
Slower spin speeds reduce wrinkling but will leave
your load more damp.
Soil
The Soil setting (wash time) is preset for each wash cycle.
For most loads, use this preset soil level. When you change
the soil setting, the cycle time will increase or decrease in the
Estimated Time Remaining display.
For heavily soiled and sturdy fabrics, use the Soil setting to
select more wash time. For lightly soiled and delicate fabrics,
use the Soil setting to select less wash time. Lower soil level
settings will help reduce tangling and wrinkling.
Presoak
Touch to add a Presoak time of your choice to a wash
cycle. Items will gently tumble through the detergent and
water for the selected time to help loosen tough stains.
OPTIONS
Touch to activate additional wash options or additional features
on the washer. Not all options are available on all models.
Steam Clean
The Steam Clean option adds additional soak and wash
time to many cycles to help remove tough stains as well
as a steam boost for added cleaning power. An integrated
heater helps to maintain optimal wash temperatures. See
the “Cycle Guide” for cycles that allow the Steam Clean
option.
EcoBoost
™
option
Touch to activate the EcoBoost
™
option. The EcoBoost
™
option provides additional energy savings through reduced
hot water usage and maintains cleaning performance by
lengthening the wash time on some cycles.
5
B
A