Conair GS11RH Iron User Manual


 
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety pre-
cautions should always be taken, including the
following:
READ ALL INSTRUCTIONS
BEFORE USING
DANGERAny appliance is elec-
trically live even when the switch is off.
To reduce the risk of death by electric shock:
1.Always “unplug it” immediately after using.
2. Do not place or store appliance where it
can fall or be pulled into a tub or sink.
3. Do not place in,or drop into water or
other liquid.
4. If an appliance falls into water, “unplug it”
immediately. Do not reach into the water.
DANGER
To reduce the risk of
burns,
electrocution, fire,or injury to persons:
1. This appliance should never be left
unattended when plugged in.
2. Close supervision is necessary when this
appliance is used by,on, or near
children or the physically challenged.
Unsupervised use could result in fire or per-
sonal injury.
3. Use this appliance only for its intended
use as described in this manual. Do not use
attachments not recommended by the man-
ufacturer.
4. Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly,or if it has been dropped or dam-
aged, or dropped into water. Do not attempt
to repair the appliance. Incorrect reassem-
bly or repair could cause a risk of fire,
electric shock, or injury to persons when
the appliance is used. Return the appliance
to an authorized service center for exami-
nation and repair.
5. Keep the cord away from heated
surfaces. Do not allow cord to contact heat-
ed surfaces. Do not pull or twist cord.Let
appliance cool completely before
putting away.Loop cord loosely around
appliance when storing.
6.This appliance has a polarized plug (one
blade is wider than the other).As a safety fea-
ture, this plug will fit in a polarized outlet only
one way.If the plug does not fit fully in the
outlet, reverse the plug.If it still does not fit,
contact a qualified electrician. Do not attempt
to defeat this safety feature.
7. Never drop or insert any object into any
opening or hose.
8. Do not use outdoors or operate where
aerosol (spray) products are being used or
where oxygen is being administered.
9. Do not use an extension cord to operate
appliance.
10. Surfaces of this appliance may be hot
when in use. Do not let eyes or bare skin
touch heated surfaces.
11. Do not place the steam nozzle directly on
any surface or on the appliance power
cord while it is hot or plugged in. Use the
stand provided.
12. Unplug this appliance before filling or
emptying. Do not overfill.
13.While emitting steam, this appliance may
cause burns if it is used too close to the
skin, scalp or eyes,or if it is used incorrectly.
To reduce the risk of contact with hot water
emitting from steam vents, test appliance
before each use by holding it away from
body.
14. Do not operate steamer without properly
filling the water container.
15.Always keep the hose and nozzle
elevated above the water container.
16. Never yank cord to disconnect from out-
let. Instead,grasp plug and pull to
disconnect.
17. Burns could occur from touching hot
metal parts, hot water, or steam. Use care
when removing water tank or when you turn
a steam appliance upside down – there may
be hot water in reservoir.
18.To reduce likelihood of circuit overload,
do not operate another high wattage appli-
ance on the same circuit.
19. If an extension cord is absolutely
necessary,a 15 ampere rated cord should
be used. Cords rated for less amperage may
overheat. Care should be taken to arrange
the cord so that it cannot be pulled or
tripped over.
20. Never pour water directly into reservoir.
21.When changing attachments, please be
sure the unit is off and no steam is being
released in order to avoid contact with hot
water.
22. Use caution when changing attachments,as
they may contain hot water from condensation.
Ensure the attachments are dry or cooled off, to
avoid contact with hot water.
SAVE THESE
INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
UNPACKING INSTRUCTIONS
Place the box on a large sturdy flat surface.
Carefully remove the appliance from the pack-
ing material. Keep all plastic bags away from
children.
STEAMER ASSEMBLY
STEP 1 - Attaching the
Telescopic Support Rod
Insert the bottom of the metal telescopic
support rod into the holder on the unit base
and screw the set screw until tight. (Caution:
Do not over-tighten.)
Attach the hose storage clip by pressing the
clip onto the lower section of the
telescopic support rod.
USING COLLAPSIBLE HANGER
This unit comes with a collapsing hanger to
use the hanger pull up on the sides of the
attachment until the arms click into the open
position. Hang your garment and steam
away wrinkles.When finished, press release
button on center of hanger to collapse for
storage.
STEP 2 - Attaching the Steamer Hose
Be sure the unit is off.Attach "T" handle
steam nozzle to steam hose.Twist clockwise to
securely lock onto hose.Tighten by hand
until handle no longer turns.
Insert angled end of hose into steamer hous-
ing and twist clockwise to securely lock
hose onto housing. (Be sure both connec-
tions at ends of hose are correct before
operating appliance.) Extend the telescopic
rod and hang the "T" handle steam nozzle
from the metal rod.
Hose may be stiff upon removal from box.
Hose will relax after initial use. T-handle
will sit properly on pole support once
hose is relaxed.
OPERATING
INSTRUCTIONS
BEFORE FILLING THE WATER CONTAINER
Turn the water container upside down and
inspect to make sure the valve and spring
assembly are functioning. Place the container
in the reservoir and check that it is seated
securely.If the container has been stored with
water inside, it may be necessary to remove
the water and clean the container. Follow the
steps for care and cleaning.
FILLING THE WATER CONTAINER
(PRIOR TO PLUGGING IN THE APPLIANCE)
Remove the water container with the handle
and turn upside down. Unscrew the valve in
the center of the base. Fill container by holding
container under a source of running cold
water until the container is filled to the desired
level. Do not overfill.Screw the valve cap onto
the water container and return the container to
the upright position. Place the water container
onto the base and make certain it is seated
properly in the cavity.DO NOT FILL THE CON-
TAINER WITH HOT WATER.
GETTING TO KNOW
YOUR STEAMER
OPERATING THE STEAMER
1. Make sure the ON/OFF switch is in the
OFF position.
2. Make sure all hose connections are
secure and tight.
3. Make sure the telescopic rod is fully
extended and the hose is not twisted
or kinked.
4. Plug the steamer cord into a normal elec-
trical outlet.
5.Turn the ON/OFF switch to the
ON position.
6.The switch will light to indicate when
power is on.
7. If the low water lamp is illuminated,
follow reset instructions.
8. Steam will be produced from the
nozzle in about one minute.
CLEANING AND STORING
I.Turn the ON/OFF switch to the OFF position
and unplug from the power source.
2.Wait for the steamer to cool completely for
at least 30 minutes.
3. Unplug power cord and gently wrap
around built-in cord wrap.
4. Remove the steamer hose.
5. Remove the water container from unit,
unscrew valve and empty unused contents.
Allow to air dry.
6. Remove excess water from the reservoir by
lifting the unit and pouring.
7. Collapse telescopic hanger rod.
8. Replace water container.
9. Store the unit.
CAUTION: Hose will be hot when
in use. Avoid prolonged contact.
Detachable cool-
touch handle
with easy grip
raised ribs
On/Off switch
Removable
5' cool-touch insu-
lated hose
with storage clip
Telescoping pole
hangs
garments and
nozzle and
collapse for stor-
age
Removable,
easy-to-fill and
easy-to-clean
2-liter water
tank with
integrated
carry handle
Collapsing
hanger
Low water
indicator
lamp
Safety auto-off
4 large casters
Cordreel
switch
04PC2300 GS11RH IB 4/10/08 11:28 AM Page 1